The transport of relativistic electron beam in compressed cylindrical targets was studied from a numerical and experimental point of view. In the experiment, cylindrical targets were imploded using the Gekko XII laser facility of the Institute of Laser Engineering. Then the fast electron beam was created by shooting the LFEX laser beam. The penetration of fast electrons was studied by observing Kα emission from tracer layers in the target.

This paper presents the design and tests of a repetitive 800 kA fast linear transformer driver (LTD) stage aimed for the Z-pinch driven fusion-fission hybrid reactor (Z-FFR).The LTD stage consists of 34 parallel basic resistor R, inductor L, and capacitor C (RLC) circuits each made up of two 100 kV/40 nF capacitors, a multi-stage gas switch and Metglas magnetic cores. The stage can deliver about 800 kA current pulse with rise time of 100 ns into the matched liquid resistive load at a repetitive frequency 0.1 Hz. A novel method to trigger the stage via a continuous internal trigger bus composed by a single cable has been proposed and demonstrated. The experimental results show that the new trigger method is feasible and reliable. A 140 kV, 25 ns rising time trigger pulse, and a 5.2 kA, 30 μs width pre-magnetization current pulse which can operate at a repetition rate 0.1 Hz were used in this stage to insure the LTD stage generating a 80 kV/800 kA current pulse every 10 s. A multi-stage gas switch that has a lifetime in excess of 10,000 shots and a jitter less than 3 ns one sigma agrees well with the demand of Z-FFR. The electrical behavior of the stage can be predicted from a simple RLC circuit, which can simplify the design of various LTD-based accelerators.

The two-temperature, 2D hydrodynamic code Hydro–ELectro–IOnization–2–Dimensional (HELIO2D), which takes into account self-consistently the laser energy absorption in a target, ionization, heating, and expansion of the created plasma is elaborated. The wide-range two-temperature equation of state is developed and used to model the metal target dynamics from room temperature to the conditions of weakly coupled plasma. The simulation results are compared and demonstrated a good agreement with experimental data on the Mg target being heated by laser pulses of the nanosecond high-energy laser for heavy ion experiments (NHELIX) at Gesellschaft fur Schwerionenforschung. The importance of using realistic models of matter properties is demonstrated.

A double layer a-CN/TiAlN coating deposited on ASP30 steel substrate was irradiated by femtosecond laser and surface modification effects were observed. Moderate laser intensities used were in the range of 1014–1013 W/cm2, while the total thickness of double layer coating was 4.8 µm (a-CN = 0.6 and TiAlN = 4.2 µm). Laser-induced changes of the surface showed dependence on laser intensity and number of accumulated pulses. Irradiations at the highest intensity resulted in preservation of one or both layers up to 10 pulses, while at lower intensity (1013 W/cm2) a-CN layer is removed after several pulses and TiAlN is preserved up to 50 pulses. Evaluated damage threshold of the target was 0.49 J/cm2. Lower laser intensity irradiation produced periodic surface structures (LIPSS) over the entire irradiated spot with periodicity of ~700 nm, almost in agreement with the laser wavelength used. Irradiations carried out at the highest laser intensity (1014 W/cm2) and laser pulse count of ≥50 resulted in the creation of crater like damages with depth up to 20 µm. Craters were conically shaped, implying intensive processes which took place at the surface. Generation of LIPSS as well as craters can be of great interest for contemporary technologies.

The effect of laser intensity on characteristics of the plasma ablated from a low-Z (CH) planar target irradiated by a 250 ps, 0.438 µm laser pulse with the intensity of up to 1016 W/cm2 as well as on parameters of the laser-driven shock generated in the target for various scale-lengths of preformed plasma was investigated at the kilojoule Prague Asterix Laser System (PALS) laser facility. Characteristics of the plasma were measured with the use of 3-frame interferometry, ion diagnostics, an X-ray spectrometer, and Kα imaging. Parameters of the shock generated in a Cl doped CH target by the intense 3ω laser pulse were inferred by numerical hydrodynamic simulations from the measurements of craters produced by the shock in the massive Cu target behind the CH layer. It was found that the pressure of the shock generated in the plastic layer is relatively weakly influenced by the preplasma (the pressure drop due to the preplasma presence is ~10–20%) and at the pulse intensity of ~1016 W/cm2 the maximum pressure reaches ~80–90 Mbar. However, an increase in pressure of the shock with the laser intensity is slower than predicted by theory for a planar shock and the maximum pressure achieved in the experiment is by a factor of ~2 lower than predicted by the theory. Both at the preplasma absence and presence, the laser-to-hot electrons energy conversion efficiency is small, ~1% or below, and the influence of hot electrons on the generated shock is expected to be weak.

A criterion for a two temperature plasma nuclear fusion ignition is derived by using a common model. In particular, deuterium-tritium (DT) and proton–boron11 (pB11) are considered for pre-compressed plasma. The ignition criterion is described by a surface in the three-dimensional space defined by the electron and ion temperatures Te, Ti, and the plasma density times the hot spot dimension, ρ·R. The appropriate fusion ion temperatures Ti are larger than 10 keV for DT and 150 keV for pB11. The required value of ρ·R for pB11 ignition is larger by a factor of 50 or more than for DT, depending on the electron temperature. Furthermore, our ignition criterion obtained here for pB11 fusion is practically impossible for equal electron and ion temperatures. In this paper it is suggested to use a two temperature laser induced shock wave in the intermediate domain between relativistic and non-relativistic shock waves. The laser parameters required for fast ignition are calculated. In particular, we find that for DT case one needs a 3 kJ/1 ps laser to ignite a pre-compressed target at about 600 g/cm3. For pB11 ignition it is necessary to use more than three orders of magnitude of laser energy for the same laser pulse duration.