This study deploys RTK-GNSS in 2012, TLS in 2015 and UAV in 2018 to monitor the changes of Urumqi Glacier No. 1 (UG1), eastern Tien Shan, and analyzes the feasibility of three technologies in monitoring the mountain glaciers. DEM differencing shows that UG1 has experienced a pronounced thinning and mass loss for the period of 2012–18. The glacier surface elevation change of −0.83 ± 0.57 m w.e. a−1 has been recorded for 2012–15, whereas the changes of glacier tongue surface elevation in 2015–18 and 2012–18 were −2.03 ± 0.95 and −1.34 ± 0.88 m w.e. a−1, respectively. The glacier area shrunk by 0.07 ± 0.07 × 10−3 km2 and the terminus retreat rate was 6.28 ± 0.83 m a−1 during 2012–18. The good agreement between the glaciological and geodetic specific mass-balances is promising, showing the combination of the three technologies is suitable to monitor glacier mass change. We recommend application of the three technologies to assess each other in different locations of the glacier, e.g. RTK-GNSS base stations, ground control points, glacier tongue and terminus, in order to avoid the inherent limitations of each technology and to provide reliable data for the future studies of mountain glacier changes in western China.

We used Sentinel-2 satellite imagery at 10 m resolution to map the extent of Norway's glaciers and ice-marginal lakes over 2018–19. We applied a standardized semi-automated band ratio method to derive glacier outlines and ice-marginal lakes. To optimise the results, we manually edited the ice-lake interfaces, debris, snow and parts of the glaciers situated under shadow. We compared our Sentinel-2 derived outlines with very high-resolution aerial orthophotos and Pléiades satellite orthoimages. Glaciers larger than 0.3 km2 have area differences within 7%, whereas values are larger for smaller glaciers. The orthophotos and orthoimages provide more details and a higher mapping accuracy for individual glaciers, but require manual digitisation, have smaller spatial and temporal coverage and can have adverse snow conditions. We found a total glacier area of 2328 ± 70 km2 of which the ten largest glaciers accounted for 52%. The glacier area decreased 15% since the previous inventory (Landsat data from 1999 to 2006), the reduction being largest in northern Norway (22%) compared to southern Norway (10%). We detected more than 2000 previously undetected smaller glaciers and ice patches (covering 37 km2) and 360 new ice-marginal lakes.

Subglacial hydrology modulates basal motion but remains poorly constrained, particularly for soft-bedded Greenlandic outlet glaciers. Here, we report detailed measurements of the response of subglacial water pressure to the connection and drainage of adjacent water-filled boreholes drilled through kilometre-thick ice on Sermeq Kujalleq (Store Glacier). These measurements provide evidence for gap opening at the ice-sediment interface, Darcian flow through the sediment layer, and the forcing of water pressure in hydraulically-isolated cavities by stress transfer. We observed a small pressure drop followed by a large pressure rise in response to the connection of an adjacent borehole, consistent with the propagation of a flexural wave within the ice and underlying deformable sediment. We interpret the delayed pressure rise as evidence of no pre-existing conduit and the progressive decrease in hydraulic transmissivity as the closure of a narrow (< 1.5 mm) gap opened at the ice-sediment interface, and a reversion to Darcian flow through the sediment layer with a hydraulic conductivity of ≤ 10−6 m s−1. We suggest that gap opening at the ice-sediment interface deserves further attention as it will occur naturally in response to the rapid pressurisation of water at the bed.

The overall trend of rapid retreat of Alpine glaciers contains considerable variability of responses at the scale of individual glaciers. As a step towards a regional assessment of glacier state that allows a detailed differentiation of single glaciers, we explore the potential of a self-organizing maps (SOM) algorithm to identify and cluster recurring patterns of thickness change at glaciers in western Austria. Using digital elevation models and glacier inventories for three time periods, we compute the frequency distribution of surface elevation change over the area of each glacier in the data set, for each period. The results of the SOM clustering show a distinct pattern shift over time: From 1969 to 1997, surface elevation change occurred at relatively uniform rates across a given glacier. Since 1997, the distribution of surface elevation change at individual glaciers has been far less uniform, indicating accelerated processes of disintegration. Tracking the evolution of individual glaciers throughout the time periods via the clusters highlights both the broader regional trend as well as glaciers that deviate from this trend, e.g. some very small, high elevation glaciers that have reverted to reduced and more uniform volume loss patterns.

Constant-load creep tests were performed at −10°C at various compressive stresses from 0.05 to 0.75 MPa on specimens taken every 10 m along a firn core extracted at Summit, Greenland in June 2017. The microstructures before and after creep testing were examined using both X-ray microtomography (micro-CT) and optical images from thin sections. An Andrade-like equation was used to describe the primary creep behavior and yielded the time exponent k of 0.17–0.76. The onset of secondary creep occurred at strains of ~0.5–3% but was sometimes not observed at all in shallow firn specimens and at stresses ⩽0.43 MPa even for strain up to 32%. For the 50–80 m firn crept at stresses ⩾0.55 MPa, secondary creep occurred at strains of 2.6 ± 0.28%, and the stress exponent, n, in Glen's law, was found to range from 4.1 to 4.6, similar to those observed for fully dense ice. Micro-CT observations of crept specimens showed that in most cases, the specific surface area, the total porosity and the structure model index decreased, while the structure thickness increased with increasing density. These microstructural characteristics are consistent with the densification of the firn. Optical images from thin sections showed that recrystallization occurred in some specimens that had undergone secondary creep.

Brash ice forms in harbours and ship channels from frequent ship passages and the resulting freezing–breaking cycles create a unique ice formation. The brash ice accumulation over the winter season is a result of meteorological, thermodynamical and mechanical processes. A reliable brash ice growth model is an important asset when determining navigation routes through ice conditions and when establishing port ice management solutions. This review aims to describe the brash ice development and its modelling as well as the key parameters that influence the brash ice growth and its estimation. This paper summarises the brash ice growth models and the fundamental theories of level ice growth upon which these models are based, and outlines the main knowledge gaps. The results highlight the importance of porosity and piece size distribution and their effect on the consolidation process. The inclusion of the brash ice lateral movement and the side ridge formation would improve the accuracy of forecast models. Furthermore, the findings of the study identify the effect of omitting meteorological parameters such as snow and radiation, from the brash ice growth models. Their contribution to the level ice thickness suggests a significant influence on the brash ice consolidation process.

Very few studies have emphasized the effects of high-pressure sintering on snow density evolution, even though snow as a type of engineering material is widely used in construction engineering in cold regions for snow pavement, snow runway and polar infrastructure. This study presents new experimental results of snow densification under high pressures of up to 100 MPa for a temperature range from −3.5 to −17.3°C and uniaxial compression at the temperature of −10°C and constant strain rates from 5 × 10−4 to 10−1 s−1. Results reveal that density evolution of snow to ice under high-pressure sintering can be achieved in a wide temperature range within a duration as short as 5 min. The compressive strength of snow-sintered ice was ~1.2–2.2 times as large as that of water-frozen ice reported by previous work. The orthogonal experiment showed that pressure is a more significant factor affecting the final density in comparison with sintering temperature and time. The increased rates of ice fabrication, low limitations on temperature and reliable sintered snow strength indicate that snow-ice engineering, such as airport construction in Greenland and Antarctica, can be improved by high-pressure sintering of snow to overcome the harsh environment.

The Wilkes Subglacial Basin in East Antarctica contains ice equivalent to 3–4 m of global mean sea level rise and is primarily drained by Cook Glacier. Of concern is that recent observations (since the 1970s) show an acceleration in ice speed over the grounding line of both the Eastern and Western portions of Cook Glacier. Here, we use a numerical ice-flow model (Úa) to simulate the instantaneous effects of observed changes at the terminus of Cook Glacier in order to understand the link between these changes and recently observed ice acceleration. Simulations suggest that the acceleration of Cook West was caused by a retreat in calving-front position in the 1970s, potentially enhanced by grounding-line retreat, while acceleration of Cook East was likely caused by ice-shelf thinning and grounding-line retreat in the mid-1990s. Moreover, we show that the instantaneous ice discharge at Cook East would increase by up to 85% if the whole ice shelf is removed and it ungrounds from a pinning point; and that the discharge at Cook West could increase by ~300% if its grounding line retreated by 10 km.

Upernavik Isstrøm, a marine glacier undergoing rapid retreat, is simulated by forcing a numerical model with ocean-driven melt. A review of processes driving retreat led us to hypothesize that a glacier undergoing rapid retreat may be less sensitive to perturbations in the balance of forces than a glacier that is undergoing moderate changes or a glacier in steady state. Numerical experiments suggest this is not the case, and that a system in rapid retreat is as sensitive to basal traction perturbations as a system that is near to steady state. This result is important when considering other glacier systems experiencing marine-forced retreat. While the ice–ocean interface is of primary importance, additional perturbations from meltwater-forced decoupling of the glacier from its bed continue to feature in glacier dynamics.

Recent regional cooling has impacted the natural systems of the Antarctic Peninsula (AP); however, little is known concerning the changes in the high parts of the glacial systems. Dry-snow line (DSL), situated in the high parts of glaciers, is the uppermost limit of frequent or occasional surface melt. We analyse dry-snow line altitude (DSLA) changes on the AP during 2004–2020 using C-band synthetic aperture radar time series data. We demonstrate that the DSLA in the eastern part of the AP is usually higher than that of the western part. Moreover, using simulated climatic variables from regional climate models, the lowering in altitude of DSL of glaciers in most areas is identified as a response to a decrease in snowmelt and an increase in precipitation. Furthermore, correlation analyses between simulated climatic variables and the DSLA are conducted. These results present the sensitive response of variations in DSLA to meteorological conditions, and the capability of DSLA being a proxy of polar local climate in high-altitude areas with no in situ meteorological observations.

The ablation zones of debris-covered glaciers in Himalaya exhibit heterogeneous processes and melt patterns. Although sub-debris melt is measured at ablation stakes, the high variability of debris thickness necessitates distributed melt measurements at the glacier scale. Focusing on Annapurna III Glacier, we used uncrewed aerial system (UAS) photogrammetry to estimate total volume loss and slope-perpendicular glacier melt between May and November 2019 using flow-corrected point clouds. Results indicated the average elevation change was −1.10 ± 0.19 m, while the mean melt was −0.87 m w.e., equating to a mean melt rate of −0.47 cm w.e. d−1. However, the spatial pattern was highly variable due to complex local processes necessitating future study over short intervals. The evaluation of specific areas showed the interplay of debris thickness variability, subseasonal debris redistribution, supraglacial channel reconfiguration and the imprint of relict ice cliffs in leading to contemporary melt rates. Ice cliffs had higher melt distances (mean −3.9 ± 0.19 m) compared to non-cliff areas (mean −0.75 ± 0.19 m) and were the predominant control on the spatial patterns of seasonal melt rates. Crucially, the definition of ice cliff areas from thinning data has a profound impact on derived melt rates and melt enhancement. Our study demonstrates the possibility and utility of deriving fully-distributed slope-perpendicular melt measurements.

Heated needle probes provide the most convenient method to measure snow thermal conductivity. Recent studies have suggested that this method underestimates snow thermal conductivity; however the reasons for this discrepancy have not been elucidated. We show that it originates from the fact that, while the theory behind the method assumes that the measurements reach a logarithmic regime, this regime is not reached within the standard measurement procedure. Using the needle probe without this logarithmic regime leads to thermal conductivity underestimations of tens of percents. Moreover, we show that the poor thermal contact between the probe and the snow due to insertion damages results in a further underestimation. Thus, we encourage the use of fixed needle probes, set up before the snow season and buried under snowfalls, rather than hand-inserted probes. Finally, we propose a method to correct the measurements performed with such fixed needle probes buried in snow. This correction is based on a lookup table, derived specifically for the Hukseflux TP02 needle probe model, frequently used in snow studies. Comparison between corrected measurements and independent estimations of snow thermal conductivity obtained with numerical simulations shows an overall improvement of the needle probe values after application of the correction.

Annual balances of eight alpine glaciers were slightly negative for 1961–90 and highly negative for 1991–2018. We explain this by changes in positive degree-day sums and summer temperatures extrapolated to the median altitudes of the glaciers. We test a new way of calculating degree-day sums that performs better than the traditional method which used daily mean temperatures. Annual degree-day sums are highly correlated with May–September temperatures as suggested in 1866 by Karl von Sonklar. We find moderate correlations between annual balances and degree-day sums, and with May–September temperatures. Calculated degree-day factors for the eight glaciers cover the reported range for snow and ice ablation, while the temperature sensitivity of annual balance is from −0.4 to −1.0 m w.e. for a +1°C temperature change. We accurately predict mean balances for 1991–2018 using May–September temperatures in regression models calibrated for 1961–90. May–September temperatures in the Alps have already increased ~+3°C since 1880 and, if temperatures continue to rise, these glaciers will shrink rapidly. As annual balances are already negative for present-day temperatures, these glaciers will not be ‘safe’ under the further temperature increase permitted by the Paris Agreement.

Polycrystalline ice is known to exhibit macroscopic anisotropy in relative permittivity (ɛ) depending on the crystal orientation fabric (COF). Using a new system designed to measure the tensorial components of ɛ, we investigated the dielectric anisotropy (Δɛ) of a deep ice core sample obtained from Dome Fuji, East Antarctica. This technique permits the continuous nondestructive assessment of the COF in thick ice sections. Measurements of vertical prism sections along the core showed that the Δɛ values in the vertical direction increased with increasing depth, supporting previous findings of c-axis clustering around the vertical direction. Analyses of horizontal disk sections demonstrated that the magnitude of Δɛ in the horizontal plane was 10–15% of that in the vertical plane. In addition, the directions of the principal axes of tensorial ɛ in the horizontal plane corresponded to the long or short axis of the elliptically elongated single-pole maximum COF. The data confirmed that Δɛ in the vertical and horizontal planes adequately indicated the preferred orientations of the c-axes, and that Δɛ can be considered to represent a direct substitute for the normalized COF eigenvalues. This new method could be extremely useful as a means of investigating continuous and depth-dependent variations in COF.

We present the first fully coupled 3D full-Stokes model of a tidewater glacier, incorporating ice flow, subglacial hydrology, plume-induced frontal melting and calving. We apply the model to Store Glacier (Sermeq Kujalleq) in west Greenland to simulate a year of high melt (2012) and one of low melt (2017). In terms of modelled hydrology, we find perennial channels extending 5 km inland from the terminus and up to 41 and 29 km inland in summer 2012 and 2017, respectively. We also report a hydrodynamic feedback that suppresses channel growth under thicker ice inland and allows water to be stored in the distributed system. At the terminus, we find hydrodynamic feedbacks exert a major control on calving through their impact on velocity. We show that 2012 marked a year in which Store Glacier developed a fully channelised drainage system, unlike 2017, where it remained only partially developed. This contrast in modelled behaviour indicates that tidewater glaciers can experience a strong hydrological, as well as oceanic, control, which is consistent with observations showing glaciers switching between types of behaviour. The fully coupled nature of the model allows us to demonstrate the likely lack of any hydrological or ice-dynamic memory at Store Glacier.

Basal conditions play an essential role in the dynamics of outlet glaciers, but direct observations at the bed of glaciers are challenging to obtain. Instead, inverse methods can be used to infer basal parameters from surface observations. Here, we use a simple ice-flow model as a forward model in an inversion scheme to retrieve the spatio-temporally variable basal stress parameter for Hagen Bræ, North Greenland, from 1990 to 2020. Hagen Bræ is a surge-type glacier with up to an order of magnitude variability of winter velocities near the grounding line. We find that downstream changes in the basal stress parameter can explain most of the variation of flow velocity, and we further identify a region of high resistance ~20–40 km from the grounding line. We hypothesise that this region of high resistance plays an important role in controlling glacier discharge.

We investigate relationships between synoptic-scale atmospheric variability and the mass-balance of 13 Andean glaciers (located 16–55° S) using Pearson correlation coefficients (PCCs) and multiple regressions. We then train empirical glacier mass-balance models (EGMs) in a cross-validated multiple regression procedure for each glacier. We find four distinct glaciological zones with regard to their climatic controls: (1) The mass-balance of the Outer Tropics glaciers is linked to temperature and the El Niño-Southern Oscillation (PCC ⩽ 0.6), (2) glaciers of the Desert Andes are mainly controlled by zonal wind intensity (PCC ⩽ 0.9) and the Antarctic Oscillation (PCC ⩽0.6), (3) the mass-balance of the Central Andes glaciers is primarily correlated with precipitation anomalies (PCC ⩽ 0.8), and (4) the glacier of the Fuegian Andes is controlled by winter precipitation (PCC ≈ 0.7) and summer temperature (PCC ≈ −0.9). Mass-balance data in the Lakes District and Patagonian Andes zones, where most glaciers are located, are too sparse for a robust detection of synoptic-scale climatic controls. The EGMs yield R2 values of ~ 0.45 on average and ⩽ 0.74 for the glaciers of the Desert Andes. The EGMs presented here do not consider glacier dynamics or geometry and are therefore only suitable for short-term predictions.

Glaciers in the Southern Patagonia Icefield (SPI) have been shrinking in recent decades, but due to a lack of field observations, understanding of the drivers of ablation is limited. We present a distributed surface energy balance model, forced with meteorological observations from a west–east transect located in the north of the SPI. Between October 2015 and June 2016, humid and warm on-glacier conditions prevailed on the western side compared to dry and cold conditions on the eastern side. Controls of ablation differ along the transect, although at glacier-wide scale sensible heat (mean of 72 W m−2 to the west and 51 W m−2 to the east) and net shortwave radiation (mean of 54 W m−2 to the west and 52 W m−2 to the east) provided the main energy sources. Net longwave radiation was an energy sink, while latent heat was the most spatially variable flux, being an energy sink in the east (−4 W m−2) and a source in the west (20 W m−2). Ablation was high, but at comparable elevations, it was greater to the west. These results provide new insights into the spatial variability of energy-balance fluxes and their control over the ablation of Patagonian glaciers.

To understand snow structure and snowmelt timing, information about flows of liquid water within the snowpack is essential. Models can make predictions using explicit representations of physical processes, or through parameterization, but it is difficult to verify simulations. In situ observations generally measure bulk quantities. Where internal snowpack measurements are made, they tend to be destructive and unsuitable for continuous monitoring. Here, we present a novel method for in situ monitoring of water flow in seasonal snow using the electrical self-potential (SP) geophysical method. A prototype geophysical array was installed at Col de Porte (France) in October 2018. Snow hydrological and meteorological observations were also collected. Results for two periods of hydrological interest during winter 2018–19 (a marked period of diurnal melting and refreezing, and a rain-on-snow event) show that the electrical SP method is sensitive to internal water flow. Water flow was detected by SP signals before it was measured in conventional snowmelt lysimeters at the base of the snowpack. This initial feasibility study shows the utility of the SP method as a non-destructive snow sensor. Future development should include combining SP measurements with a high-resolution snow physics model to improve prediction of melt timing.