A study on the microwave performance of a metallic transmission line capable of simultaneously transmitting microwave and optical signals is presented targeting millimeter-long interconnects. Conventional analytical solution is used to find the optimal structure for a given characteristic impedance. Then, functionality of the link is validated through S-parameter measurements for 3–13 mm long lines. The waveguide parameters, such as resistance, inductance, capacitance, and conductance are extracted based on a lumped circuit model. The modeling enables structure optimization for interconnect bandwidth density of 1 Gb/s/μm and more.

The paper presents a two-dimensional (2D) extended envelope memory polynomial model for concurrent dual-band radio frequency (RF) power amplifiers (PAs). The model is derived based on the physical knowledge of a dual-band RF PA. The derived model contains cross-modulation terms not included in previously published models; these terms are found to be of importance for both behavioral modeling and digital predistortion (DPD). The performance of the derived model is evaluated both as the behavioral model and DPD, and the performance is compared with state-of-the-art 2D-DPD and dual-band generalized memory polynomial (DB-GMP) models. Experimental result shows that the proposed model resulted in normalized mean square error of −51.7/−51.6 dB and adjacent channel error power ratio of −63.1/−63.4 dB, for channel 1/2, whereas the 2D-DPD resulted in the largest model error and DB-GMP resulted in model parameters that are three times more than those resulted with the proposed model with the same performance. As pre-distorter, the proposed model resulted in adjacent channel power ratio of −55.8/−54.6 dB for channel 1/2 and is 7–10 dB lower than those resulted with the 2D-DPD model and 2–4 dB lower compared with the DB-GMP model.

This paper presents an optimized ink-reducing meander dipole antenna structure suitable for implementing printed radio frequency identification (RFID) tags. The proposed antenna designs contain empty ink-reducing hollowed-out areas along the antenna's arms such that the resulting antennas require much less conductive ink to produce yet still achieve decent antenna performance compared with the conventional solid-arm dipole antennas. The simulation results demonstrate that when the ratio between the width of the hollowed-out areas and the width of the antenna arms is about 0.6, the resulting RFID tag experiences a slight read range performance degradation of <10%, while it offers a sizeable ink consumption reduction of almost 50%.

This paper presents and discusses several methods for predicting the low-frequency (LF) noise at the output of a mm-wave detector. These methods are based on the extraction of LF noise source parameters from the single diode under a specific set of bias conditions and the transfer or conversion of these noise sources, under different operating conditions including cyclostationary regime, to the quasi-dc output of a mm-wave detector constructed with the same model of diode. The noise analysis is based on a conversion-matrix type formulation, which relates the carrier noisy sidebands of the input signal with the detector output spectrum through a pair of transfer functions obtained in commercial software. Measurements of detectors in individual and differential setups will be presented and compared with predictions.

A simple electromagnetic model of wind-turbine's main structural elements as the linear wired structures is developed to simulate the temporal patterns of observed radar return Doppler spectra (micro-Doppler). Using the model, the micro-Doppler for different combinations of the turbines rotation frequency, radar pulse repetition frequency, and duration of the Doppler measurement interval are analyzed. The model is validated using the PARSAX radar experimental data. The model ability to reproduce the observed Doppler spectra main features can be used for development of signal-processing algorithms to suppress the wind-turbines clutter in modern Doppler radars.

Different types of bondwire interconnect for differential chip-to-antenna and single-ended chip-to-chip interfaces are investigated. Two differential compensation structures for various lengths of interconnects are designed and experimentally evaluated using dedicated transmit and receive radar modules operating across a 110–156 GHz band. Measurement results demonstrate that a fractional bandwidth of 7.5% and a minimum insertion loss of 0.2 dB can be achieved for differential interconnects as long as 0.8 mm. Design and measurement results of an extremely wideband low-loss single-ended chip-to-chip bondwire interconnect that features 1.5 dB bandwidth from DC to 170 GHz and insertion loss of less than 1 dB at 140 GHz are presented as well. The results show that the well-established wire-bonding techniques are still an attractive solution even beyond 100 GHz. Reproducibility and scalability of the proposed solutions are assessed as well.