The μ-negative metamaterial (MNG) two-element MIMO antenna design was proposed in this article for WiMAX (2.5–2.8 GHz), WLAN (3.2–5.9 GHz), and ITU band (8.15−8.25 GHz) applications. The first design of the MIMO antenna operates at 2.7 and 4.9 GHz frequencies. In order to reduce the mutual coupling, a defective ground structure is used. For further isolation improvement, an MNG unit cell is placed in between the two radiating elements at a distance of 10 mm. The designed antenna elements have better than −23 dB coupling isolation between the two radiating elements. Moreover, with MNG an additional frequency of 8.2 GHz is obtained, which is useful for ITU band applications. The proposed antenna bandwidth is expanded by 19% in the lower operational band, 20% in the second operational band, and 32% in the higher frequency band with the MNG unit cell. From the analysis, the proposed antenna is suitable for WiMAX/WLAN/ITU band applications because of its low enveloped correlation coefficient, and highest directive gain and low mutual coupling between the radiating components. The proposed antenna was simulated, fabricated, and measured with the help of the Schwarz ZVL vector network analyzer and anechoic chamber. Both measured and simulated results are highly accurate and highly recommended for WiMAX/WLAN/ITU bands.

This paper presents a simple and compact coplanar waveguide (CPW)-fed circular-shaped reconfigurable patch antenna with a switchable circular polarization (CP) sense. The circular patch is cut at the ends vertically and switches are introduced to connect the patch ends. By controlling the ON/OFF status of the two switches, the polarization of the antenna can be switched between two states: left-hand circular polarization and right-hand circular polarization. The patch is designed on a very thin RT Duroid substrate of dielectric constant (εr) of 2.2 and thickness of 0.254 mm. The overall antenna dimensions are 35 × 30 mm. The antenna is designed and simulated using finite-element method -based EM simulator, HFSS. For each switching condition the return loss curve, radiation pattern are obtained. Axial ratio curves for polarization diversity cases are also plotted. Parametric studies have been made in order to get optimized values for certain antenna dimensions such as thickness, CPW ground to feed gap, etc.

This paper presents measurement results providing the mapping of the opto-microwave transfer function performed on an SiGe microwave heterojunction phototransistor (HPT). This measurements will be used to extract a guideline for designing phototransistors. A mapping of the HPT's gain in low frequency helps to estimate the shape of the optical beam used for the measurement. The study also focuses on the cutoff frequency mapping of the device in phototransistor mode. Finally, these results are used to determine the general optimization rules in the SiGe HPTs design.

This paper describes some key points of a new tool being currently developed by Eurocontrol for the assessment of air traffic control (ATC) multisensor trackers performance. It summarizes the algorithmic foundations of the high-accuracy trajectory reconstruction process used to obtain reference trajectories from recorded measures. These trajectories will serve as a reference for the evaluation of the accuracy of ATC data processing centers. The performance of the system is illustrated with some reconstruction experiments on synthetic and real data.

In this study, the problem of backward heating in microwave ablation technique is examined and an electromagnetic solution based on the use of high impedance graphene material is presented for its mitigation. In this context, a one-atom-thick graphene layer is added on the coaxial double slot antenna. In addition to the electromagnetic behavior, thermal effects caused by the graphene-covered antenna are emphasized. The graphene's conductivity being highly dependent on its chemical potential and the relaxation time, a parametric study is performed to determine a range of tolerances within which the graphene-coated antenna outperform a typical graphene-free antenna. The range of values is found to be 0 < μc < 0.5 eV and τ < 0.4 ps, for the chemical potential and the relaxation time, respectively. The backward heating problem being prevented, the ablation region is ensured to be spherical around the tip of the antenna. Effects of the graphene layer to the heat dissipation in the tissue, the necrotic tissue ratio (damage to the cancerous tissue of the caused by electromagnetic energy), and the treatment time using the coaxial double slot antenna were examined. The results show that the heat dissipation is concentrated around the slots (region of cancerous tissue) and a higher necrotic tissue ratio can be achieved with a graphene-covered double slot antenna in a shorter time.

This paper presents the behavior of three iterations of a coplanar waveguide fed CANTOR Set fractal antenna. This kind of antennas allows having a broadband behavior and important gains. Also, the setup of slots allows having more lower resonant frequencies and therefore designing miniaturized antennas with good performances. The proposed antennas are suitable for 2.5/3.3/5/5.5 GHz worldwide interoperability for microwave access and for 2.4–2.5/4.9–5.9 GHz wireless local area networks applications. The simulations were performed in FEKO 6.3. The measurements were performed with Vector Network Analyzer HP 8719C.

In this paper, the designs and experimental performances of wideband (higher than one octave) high-efficiency, high-power amplifiers (HPA) working in the 1–4 GHz range, using the same GaN process, are presented. They are based on the Bode–Fano integrals, which can be applied to a trade-off calculation between bandwidth and efficiency. Firstly, an microwave intregrated circuits (MIC) wideband HPA, externally matched, is presented. It generates a continuous wave (CW) output power (Pout) greater than 40 W, a power gain (GP) higher than 9.2 dB and a corresponding power added efficiency (PAE) (drain efficiency (DE)) ranged between 36 and 44% (40 and 48%) over the 1–3 GHz bandwidth. Two other amplifiers have been designed upon the same theoretical methodology, with a passive GaAs MMIC circuit technology, enabling to reduce the final size down to 420 mm2. The first internally matched Quasi monolithic microwave intergrated circuits (Quasi-MMIC) single-ended HPA generates a pulsed Pout greater than 25 W, GP higher than 9.8 dB, and a corresponding PAE (DE) ranged between 37 and 52.5% (40 and 55%) over the 2–4 GHz bandwidth. The second internally matched Quasi-MMIC HPA, based on balanced architecture, generates a pulsed Pout higher than 45 W, GP higher than 9.5 dB and PAE (DE) ranged between 33 and 44% (38 and 50%) over the 2–4 GHz bandwidth. These results are among the best ones published in terms of PAE and Pout in instantaneous octave bandwidth in the 1–4 GHz frequency range.

Multiple input multiple output (MIMO) systems, which use multiple antennas to deliver faster data rates, are one of the promising methods in 5G services. 5G is a popular issue among the world's main telecom firms currently. The sub-6 GHz band for 5G applications in various countries lies between 3 and 5 GHz. The sub-6 GHz 5G bands are 3.4–3.8 GHz in Europe, 3.1–3.55 GHz in the USA, and 3.3–3.6 GHz and 4.8–4.99 GHz in China. This paper presents a two-element slotted octagon-shaped antenna operating in the sub-6 GHz band (3.1–4.5 GHz) for 5G applications. A T-formed isolation structure is placed at a ground plane to minimize mutual coupling between MIMO antennas. The proposed MIMO antenna has physical dimensions of 55 × 38 mm2 and an envelope correlation coefficient or correlation of 0.0004 over the entire operating band. The antenna operates at 3.6 GHz, with a return loss of 40.8 dB at the resonance. An antenna prototype has been investigated and proven to be of excellent quality in terms of performance like isolation >20 dB, efficiency >80%, and mean effective gain <−3 dB over the full operating band.

The pulse radiating characteristic of a wrapped bow-tie antenna (WBA) and wrapped resistively loaded bow-tie antenna (WRLBA) is presented for impulse radar applications in this paper. The numerical analysis of the WRLBA is performed by comparing that of the WBA. The wrapped antennas are realized on a flexible substrate. The antennas are fed by an impedance tapered balun, which has an overall transmission loss of −1.4 dB over the balun length. The characteristics of the resistive loading to the wrapped antenna, such as reflection coefficient, reflected pulse in the time domain, voltage standing wave ratio, and input impedance, are experimentally investigated and compared with simulated results. The fidelity factor of the radiated electric field on the boresight direction for the WBA and WRLBA is calculated as 0.82 and 0.96, respectively. The wireless communication ability is evaluated by the transmission coefficient, group delay, boresight gain, and received waveform. The calculated fidelity factor of the received waveform for the WBA and WRLBA is 0.79 and 0.85, respectively. The average and variations of the group delay of both wrapped antennas are observed to be around 2.5 ns and less than 1.5 ns, respectively.

In this research article, a metasurface (MTS)-loaded high-gain and broadband circularly polarized (CP) monopole antenna is reported. The proposed antenna configuration consists of a symmetric Y-shaped radiating monopole over a partial ground plane with extended twin parasitic conducting strips (PCS) loaded with a MTS reflector. To achieve left-hand circular polarization characteristics, a metallic copper strip is utilized to short the partial ground plane with one of the twin PCS [PCS(L)]. By using the grid-slotted sub patches on a rectangular MTS a reflector of 2λfa × 1.65λfa × 0.02λfa is placed just below the monopole radiator at a height of 0.33λfa, which provides broadened impedance (IBW) and 3 dB axial ratio bandwidth (ARBW) responses with high gain. The proposed prototype with an volumetric dimension of 1.33λfa × 0.9λfa × 0.02λfa at fa = 5 GHz is designed and characterized. It exhibits a measured IBW of 48.45% (3.57–5.89 GHz), ARBW of 25.25% (4.21–5.42 GHz), and CP gain of > 8.35 dBic with the antenna efficiency of > 75% in the desired operating frequency bands. The obtained performances of the proposed MTS antenna confirm its suitability for RF energy harvesting application.

A flexible and adaptive energy-efficient high-speed wireless hub is developed in polymer foil as a Hybrid System-in-Foil (HySiF) using Chip-Film Patch (CFP) technology. In this matter, the SiGe BiCMOS silicon chips (2.39 × 1.65 mm2) are thinned down to 45 μm and are embedded face-up inside a two-polymer CFP carrier. The active pads of the embedded silicon chips inside foil are extended to the surface of the foil to interconnect to the antenna on the foil. The integrated hybrid system has a signal transmission at 5–6 GHz frequency band. The overall thickness of the system is below 100 μm and its bendability is down to 4 mm radius of curvature. The designed and fabricated PA silicon chips operate at 50 mA with a 1.5 V supply voltage. Therefore, in addition to the high lateral thermal resistance of the thinned chip, self-heating loop inside polymer due to the low thermal conductivity of the embedding polymer raises the system temperature. Consequently, the thermal behavior and RF performance of the PA chip under different conditions are investigated. Moreover, the antenna with the required carrier frequency is simulated, fabricated, and measured on top of the polymer foil as a stand-alone system in the flexible CFP.

This paper presents the technical realization of the multiple-input multiple-output (MIMO) radar MIRA-CLE Ka (MIMO radar-configurable in Ka-band). This system is a stationary imaging radar without any mechanical moving parts. It is highly portable, ready to use in only a couple of minutes, and it is able to process one radar image per second during continuous radar measurements in the current stage of development. In addition to the image processing, it is possible to detect changes in range of 0.1 mm in the illuminated scene. The MIMO system operates in Ka band and consists of 16 receive and 16 transmit elements, so that 256 virtual elements are generated during signal processing. The size of the antenna's frontend is about 80 cm in width. Owing to its compact size, flexibility, and realtime capability, the system offers a wide field of applications.

In this paper, a novel circularly polarized square slot microstrip antenna is proposed for radio frequency identification (RFID) applications. The circular polarization is achieved by incorporating an arc-shaped strip in the square slot antenna. This antenna is fed by deformed bent feeding line to achieve a broad bandwidth (BW). The key parameters of the antenna are used for parametric study to understand the influence on the antenna performance. To validate simulation results of the design, a prototype is fabricated on the commercially available FR4 material. Measured results show a good agreement with the simulated results. It is found that the antenna shows an impedance BW of 170 MHz (844–1014 MHz) and axial-ratio BW of 170 MHz (834–1004 MHz), which shows that the proposed antenna is a good candidate to be used as a RFID antenna.

This paper describes a linear-polarized reflector that reflects incident wave almost parallel to its surface at 60 GHz, when illuminated by an impinging plane wave with normal incidence. This structure is designed as a simple and low-cost passive repeater with both a quasi-endfire radiation and a flat profile. Working as a transmission relay, it is a quite potential and possible solution to improve the radio-coverage in the T-shaped corridor, which is a typical scenario of non-light-of-sight (NLOS) environment for 60 GHz indoor communications. The proposed repeater consists of an array of parallel grooves with appropriate depths, drilled in a metallic plate. Full-wave simulations and theoretical investigations are carried out to demonstrate the working principle and to optimize the performance. Then, an 80-groove breadboard in the size of 200 mm × 200 mm is fabricated and measured to explore the feasibility of the concept. In a practical measurement, when the distance from the repeater to transmitting antenna (Tx) is 2 m, and to the receiving antenna (Rx) is 1.5 m, the repeater exhibits a main beam at ±75° with gain up to 22.7 dB. The communication between Tx and Rx in NLOS areas is thus successfully recovered.

A novel transmission-line model is used for the analysis of planar structures, including wire-medium (WM) slabs with vertically aligned wires. The network formalism allows for an effective determination of the relevant spectral Green's functions, of the modal dispersion equation via transverse resonance, as well as of the far-field radiation pattern produced by simple sources via reciprocity, as opposed to the more cumbersome field-matching approach. Numerical results, validated also against state-of-the-art simulation software, confirm the accuracy and effectiveness of the proposed approach. In particular, modal and radiation features are presented for a class of leaky-wave antennas based on planar WM loaded configurations covered by partially reflecting screens, for which leaky unimodal regimes are achieved by minimizing spurious radiation from the quasi-transverse electromagnetic (TEM) mode.

In this paper, a triple-band 1 × 2 and 1 × 4 microstrip patch antenna array for next-generation wireless and satellite-based applications are presented. The targeted frequency bands are 3.6, 5.2 and 6.7 GHz, respectively. Simple design procedures and optimization techniques are discussed to achieve better antenna performance. The antenna is designed and simulated using Agilent ADS Momentum using FR4 substrate (εr = 4.2 and h = 1.66 mm). The main patch of the antenna is designed for 3.6 GHz operation. A hybrid feed technique is used for antenna arrays with quarter-wave transformer-based network to match the impedance from the feed-point to the antenna to 50 Ω. The antenna is optimized to resonate at triple-bands by using two symmetrical slits. The single-element triple-band antenna is fabricated and characterized, and a comparison between the simulated and measured antenna is presented. The achieved simulated impedance bandwidths/gains for the 1 × 2 array are 1.67%/7.75, 1.06%/7.7, and 1.65%/9.4 dBi and for 1 × 4 array are 1.67%/10.2, 1.45%/8.2, and 1.05%/10 dBi for 3.6, 5.2, and 6.7 GHz bands, respectively, which are very practical. These antenna arrays can also be used for advanced antenna beam-steering systems.

This paper presents different reconfigurable antennas with frequency, polarization, and pattern diversities. All the antennas have a very simple, novel, and compact structures, which are used for different wireless communication applications. These antennas employ switching for obtaining different reconfigurations. At first, an E-shaped antenna is designed for multi-band frequency reconfigurability. Second, circular and rectangular-shaped patch antennas are designed for achieving diversity in polarization. At last, a pattern reconfigurable antenna is designed with multiport excitation. These antenna performances are analyzed using various parameters such as return loss, radiation pattern, voltage standing wave ratio (VSWR), and gain. The prototypes of the antennas are fabricated and measured results along with simulated ones are presented. Both the results are in good agreement.

In this paper a novel approach for determining the four noise parameters of FET devices over frequency is presented. Such methodology is made of two parts: the first one allows to straightforwardly extract single-frequency noise parameters from source-pull data; the second one extends this capability to multi-frequency, source-pull data to obtain a full description of device noise behavior over frequency by means of at most 10 constant parameters (depending on the required accuracy). The whole process is automated via a software routine and does not need a previous knowledge of the FET equivalent circuit's topology, or the values of its elements. This peculiarity makes the proposed method very well suited to quick characterization campaigns of active devices, avoiding the burden of a whole set of prior, different measurements and the relevant, critical extraction procedures, which are strongly dependent on the device.

A new microstrip lowpass filter with compact size and ultra-wide stopband using T-shaped resonator is proposed. To make smaller the circuit size of the filter, cursive transmission line is also suggested. Moreover, exact equation of most important transmission zero is calculated based on LC equivalent circuit and transformation function. A demonstration filter with 3 dB cut-off frequency at 1.02 has been designed, fabricated, and measured. Results show that a relative stopband band width of 166.3% (referred to suppression degree of 20 dB) is achieved while obtaining high figure of merit of 46 274.

Two types of optoelectronic oscillators delivering high spectral purity microwave signals are presented in this paper. These oscillators use the Pound–Drever–Hall laser stabilization technique to lock the laser carrier onto two different types of passive optical resonators featuring high-quality factors: a fiber ring resonator (FRR) and a whispering gallery mode monocrystalline disk-shaped micro-resonator. The different noise processes occurring inside these oscillators are discussed. Particular attention is given to the conversion of the laser's amplitude and frequency noise into RF phase noise via the laser stabilization loop and the resonator, and via the photodetector nonlinearity as well. A modeling approach using CAD software is also proposed to qualitatively evaluate laser noise conversion through the optical resonator. Moreover, different contributions of nonlinear optical scattering noise are discussed, mainly in the case of the FRR-based oscillator. When controlling these nonlinear optical effects in the case of the FRR, low-phase noise operation of the oscillator has been achieved, with a −40 dBc/Hz noise level at 10 Hz offset frequency from a 10.2 GHz RF carrier.