Natural and synthetic micas have been used widely as substrates to study biological systems; but, as in the case of negatively charged DNA, anionic charge repulsion may render micas a less than ideal templating surface for many biological systems. The purpose of this study was to investigate the potential for the chlorite clinoclore, which contains a positively charged interlayer octahedral sheet, to serve as a substrate for DNA adsorption. The relationships between clinochlore cleavage characteristics, in terms of nano-morphology, and surface potential are investigated, as are its average crystal chemistry and topology. That the structural features of clinochlore can be used successfully to condense, order, and self assemble complex biomolecules, such as DNA is also proven.

A natural IIb-4 clinochlore [$C\overline{1}$\$\end{document} symmetry, unit-cell parameters a = 0.53301(4); b = 0.92511(6); c = 1.4348(1) (nm); α = 90.420(3); β = 97.509(3); γ = 89.996(4) (°)] with chemical composition $\left({\text{Mg}}_{1.701}{\text{Fe}}_{0.245}^{2+}{\text{Ti}}_{0.004}{\text{Al}}_{0.998}{\text{Cr}}_{0.052}^{3+}\right){\text{Mg}}_3\left({\text{Si}}_{2.939}{\text{Al}}_{1.015}{\text{Fe}}_{0.046}^{3+}\right){\text{O}}_{10}\left({\text{OH}}_{7.913}{\text{F}}_{0.087}\right)$\$\end{document} was selected. The octahedral sites of the silicate layer (<M(1)−O> = 0.2080 nm and <M(2)−O> = 0.2081 nm) are equal and occupied by Mg, whereas the octahedral sites in the interlayer M(3) and M(4) (<M(3)−O> = 0.2088 nm and <M(4) − O> = 0.1939 nm) show different sizes and are mostly completely occupied by divalent (Mg2+ and Fe2+) and trivalent (Al3+) cations, respectively.

The clinochlore cleaved surface is present in two forms: (1) the stripe type (0.40 nm in height, up to several micrometers long and ranging from some nanometers to a few microns in lateral size); and (2) the triangular type (0.40 nm in height). Both features may result either from interlayer sheets whose cleavage weak directions are related to the different M(3) and M(4) site occupancy, or from weak interlayer bonding along specific directions to the 2:1 layer underneath. The cleaved surface, particularly at the cleaved edges, presents high DNA affinity, which is directly related to an average positive surface and ledge potential.

Palmer amaranth is the most common and troublesome broadleaf weed species of rice in Mississippi because of the effects of early-season interference and infestations on rice levees, and herbicides for residual or POST control of Palmer amaranth in rice are limited. Three studies were conducted in 2012 and 2013 to evaluate application rates and timings of saflufenacil in rice and to determine the influence of adjuvants when mixed with saflufenacil applied POST. In a PRE study, no injury occurred after saflufenacil PRE, and no control was observed from carfentrazone. Hemp sesbania and Palmer amaranth control increased with increasing saflufenacil rate when applied PRE. Hemp sesbania control with saflufenacil at any rate PRE was ≤ 25% at 35 d after treatment (DAT). Palmer amaranth and ivyleaf morningglory control with saflufenacil at 75 g ai ha−1 PRE was ≥ 94% 35 DAT. In a POST study, rice injury was influenced by application timing and rate of saflufenacil; however, efficacy was not. Rice injury with saflufenacil at 25 g ha−1 and carfentrazone early POST (EPOST) and late POST was similar 7 DAT. Saflufenacil at 50 and 75 g ha−1 EPOST were the most injurious 7 DAT. Control of hemp sesbania and ivyleaf morningglory was similar for all rates of saflufenacil and carfentrazone; however, Palmer amaranth control with saflufenacil at any rate was greater than that of carfentrazone 14 and 28 DAT. In an adjuvant study, rice injury was influenced by adjuvant and saflufenacil rate. Saflufenacil applied alone or in mixture with crop oil concentrate (COC) was least injurious, and saflufenacil at 50 g ha−1 was more injurious than saflufenacil at 25 g ha−1. Saflufenacil applied in combination with any adjuvant provided better control of hemp sesbania and Palmer amaranth than saflufenacil alone. On the basis of this research, saflufenacil should be applied PRE at 50 or 75 g ha−1, depending on weed spectrum, and POST applications should be made at 25 g ha−1 in combination with COC after the two-leaf rice growth stage.

Dense populations of glyphosate-resistant (GR) Italian ryegrass are problematic for spring burndown herbicide programs and crop establishment in the midsouthern United States. Two field studies were conducted to evaluate fall-applied residual herbicides for control of GR Italian ryegrass and to identify the most effective application timing for these herbicides. Fall applications of clomazone at 0.84 and 1.12 kg ai ha−1, pyroxasulfone at 0.16 kg ai ha−1, and S-metolachlor at 1.79 kg ai ha−1 controlled GR Italian ryegrass ≥ 93% 180 d after application. Control from incorporated applications of pendimethalin at 1.59 kg ai ha−1 and trifluralin at 1.68 kg ai ha−1 and surface applications of S-metolachlor at 1.42 kg ha−1 provided control similar to the best treatments. Glyphosate-resistant Italian ryegrass control following clomazone, pyroxasulfone, S-metolachlor, or trifluralin applied in mid September, October, or November exceeded that from fall tillage by 19 to 56% at 90 and 140 d after the last treatment. Pyroxasulfone and S-metolachlor controlled more GR Italian ryegrass following October or November applications compared with those in September at both 90 and 140 d after the last application timing. However, the benefit of delaying clomazone application from October to November was not realized until the last evaluation (140 d after the last treatment). Clomazone, pyroxasulfone, and S-metolachlor offer growers the best opportunity for residual control of GR Italian ryegrass, and control is optimized when these herbicides are applied in November.