Hostname: page-component-7bb8b95d7b-5mhkq Total loading time: 0 Render date: 2024-10-04T05:06:06.487Z Has data issue: false hasContentIssue false
  • English
  • Français

A Highly Reliable Al Line with Controlled Texture and Grain Boundaries

Published online by Cambridge University Press:  15 February 2011

M. Hasunuma ,
H. Toyoda ,
T. Kawanoue ,
S. Ito ,
H. Kaneko  and
M. Miyauchi
M. Hasunuma
Affiliation:
Toshiba Corp., Research and Development center, Materials and Devices Lab. 1, Komukai Toshiba-cho, Saiwaiku, Kawasaki, 210, Japan
H. Toyoda
Affiliation:
Toshiba Corp., Research and Development center, Materials and Devices Lab. 1, Komukai Toshiba-cho, Saiwaiku, Kawasaki, 210, Japan
T. Kawanoue
Affiliation:
Toshiba Corp., Research and Development center, Materials and Devices Lab. 1, Komukai Toshiba-cho, Saiwaiku, Kawasaki, 210, Japan
S. Ito
Affiliation:
Toshiba Corp., Research and Development center, Materials and Devices Lab. 1, Komukai Toshiba-cho, Saiwaiku, Kawasaki, 210, Japan
H. Kaneko
Affiliation:
Toshiba Corp., Research and Development center, Materials and Devices Lab. 1, Komukai Toshiba-cho, Saiwaiku, Kawasaki, 210, Japan
M. Miyauchi
Affiliation:
Toshiba Corp., Research and Development center, Materials and Devices Lab. 1, Komukai Toshiba-cho, Saiwaiku, Kawasaki, 210, Japan
Get access

Abstract

In order to clarify the relationship between Al line reliability and film microstructure, especially grain boundary structure and crystal texture, we have tested three kinds of highly textured Al lines, namely, single-crystal Al line, quasi-single-crystal Al line and hypertextured Al line, and two kinds of conventional Al lines deposited on TiN/Ti and on SiO2. Consequently, the empirical relation between the electromigration (EM) lifetime of Al line † and the (111) full width at half maximum (FWHM) value ω is described by † ∝ ω-2 [1]. This improvement of Al line reliability results from as following reasons; firstly, homogeneous microstructure and high activation energy of 1.28eV for the single-crystal Al line (ω=0.18°); secondly, sub-grain boundaries which consisted of dislocation arrays found in the quasi-single-crystal Al line (ω=0.26°) has turned out to be no more effective mass transport paths because dislocation lines are perpendicular to the direction of electron wind. Although there exist plural grain boundary diffusion paths in the newly developed hypertextured Al line (ω=0.5°) formed by using an amorphous Ta-Al underlayer {1], the vacancy flux along the line has been suppressed to the same order of magnitude of single crystal line. It has been clarified that the decrease of FWHM value has promoted the formation of sub-grain boundaries and low-angle boundaries with detailed orientation analysis of individual grains in the hypertextured film. The longer EM lifetime for the hypertextured Al line is considered to be due to the small grain boundary diffusivities for these stable grain boundaries, and this diffusivity reduction resulted in the suppression of void/hillock pair in the Al lines. These results have confirmed that controlling texture and/or grain boundary itself is a promising approach to develop reliable Al lines which withstand higher current densities required in future ULSIs.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 391: Symposium T – Materials Reliability in Microelectronics V , 1995 , 335
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Toyoda, H., Kawanoue, T., Hasunuma, M., Kaneko, H. and Miyauchi, M., Proc.32nd Ann. Int'l.Reliab.Phys.Symp IEEE, 178(1985)Google Scholar
2 Towner, J.M., Darks, A.G. and Tien, T., Proc.24th Ann. Int'l. Reliab.Phys.Symp., IEEE, 7(1986)Google Scholar
3 Hosoda, T., Yagi, H. and Tstuchikawa, T., Proc.27th Ann. Int'l. Reliab.Phys.Symp., IEEE, 202(1989)Google Scholar
4 Onuki, J., Koibuchi, Y., Fukada, S., Suwa, M., Misawa, Y. and Itagaki, T., IEDM Tech. Dig., JEEE, 454(1988)Google Scholar
5 Ogawa, S. and Nishimura, H., IEDM Tech.Dig.,IEEE, 277(1991)Google Scholar
6 Lin, T., Ahn, K.Y., Harper, J.M.E. and Chaloux, P.N., IEEE VMIC Conf., 76(1988)Google Scholar
7 Hinode, K. and Honma, Y., Proc.28th Ann. Int'l. Reliab.Phys.Symp., IEEE, 25(1990)Google Scholar
8 Ho, P.S., Howard, J.K. and White, J.F., J.Appl.Phys., 49 , 4083 (1978)Google Scholar
9 Kawanoue, T., Kaneko, H., Hasunuma, M. and Miyauchi, M., J.Appl.Phys., 7 4 (7), 4423(1993)Google Scholar
10 Vaidya, S. and Shinha, A.K., Thin Solid Films, 75, 253 (1981)Google Scholar
11 Knorr, D.B. and Lu, T.M., Appl.Phys.Lett., 54, 2210(1989)Google Scholar
12 Lytle, S.A. and Oates, A.S., J.Appl.Phys., 71 (1), 174(1992)Google Scholar
13 Marieb, T.N., Abratowski, E., Bravman, J.C., Madden, M. and Flinn, P., AIP Conf. Proc. No.305 (edited by P.S.Ho, , C.Y.Li, and P.Totta, ), 1(1994)Google Scholar
14 Yue, J.T., Funsten, W.P. and Taylar, R.V., Proc.23th Ann. Int’l. Reliab.Phys.Symp., IEEE, 1 (1985)Google Scholar
15 , Tanikawa, Okabayashi, H., Mori, H. and Fujita, H., Proc.28th Ann. Int'l. Reliab. Phys. Symp., IEEE, 209(1990)Google Scholar
16 Kaneko, H., Hasunuma, M., Sawabe, A., Kawanoue, T., Kohanawa, Y., Komatsu, S. and Miyauchi, M., Proc .28th Ann.Int’l. Reliab.Phys.Symp., IEEE, 194(1985)Google Scholar
17 Hasunuma, M., Kaneko, H., Sawabe, A., Kawanoue, T., Kohanawa, Y., Komatsu, S. and Miyauchi, M., IEDM Tech.Dig.,IEEE, 677(1989)Google Scholar
18 Hinode, K., Owada, N., Nishida, T. and Mukai, K., J. Vac.Sci.Technol., B5, 518(1987)Google Scholar
19 Gangulee, A. and d'Heurle, F.M., Thin Solid Films,16, 227(1973)Google Scholar
20 Kobayashi, T., Sekiguchi, A., Akiyama, N., Hosokawa, N. and Asamaki, T., J.Vac.Sci.Technol., A 10, 525(1992)Google Scholar
21 Yamada, I., Inokawa, H. and Takagi, T., J.Appl.Phys., 56, 2746 (1984)Google Scholar
22 d'Heurle, F., Berenbaum, L. and Rosenberg, R., Tran. of AIME, 242, 502 (1968)Google Scholar
23 Kaneko, H., Kawanoue, T., Hasunuma, M. and Miyauchi, M., AIP Conf. Proc. No.305 (edited by P.S.Ho, , C.Y.Li, and P.Totta, ),179 (1994)Google Scholar
24 Messer, R., Dais, S. and Wolf, D., Proc. 18th Ampere Congress (Nottingham, England),1974 Google Scholar
25 Balluffi, R.W., Met. Trans., 13B,527(1982)Google Scholar
26 Wolf, D., J.Mater.Res., 5,1708(1990)Google Scholar