Hostname: page-component-78c5997874-4rdpn Total loading time: 0 Render date: 2024-11-16T15:26:07.882Z Has data issue: false hasContentIssue false
  • English
  • Français

Cu Post-CMP Displacement Cleaning: A Mechanistic Product Development Approach Based on Selected Thermodynamic and Kinetic Data

Published online by Cambridge University Press:  01 February 2011

Darryl Wayne Peters
Darryl Wayne Peters*
Affiliation:
[email protected], Paragon Consultants, Semiconductor Applications, 111 Kennedy Mill Road, Stewartsville, NJ, 08886, United States, 484-515-7186, 908-479-1349
Get access

Abstract

A mechanistic product development approach will be presented that utilized selected thermodynamic and kinetic data for development of a Cu post-CMP cleaner for use after polishing with either high or low pH slurry. A Pourbaix diagram offers the thermodynamically stable Cu species vs. pH and open circuit potential (OCP) for an aqueous cleaner. Pourbaix diagrams do not provide any information on the kinetics for dissolution of water soluble species. Cu oxide dissolution rates were measured using an electrochemical cell. Deposition and removal rates for benzotriazole (BTA) and 1,2,4-triazole (TAZ) were measured using an electrochemical cell with a quartz crystal microbalance (QCM). Passivator film deposition was investigated to determine the film type and thickness resulting from a typical CMP process. BTA and TAZ films deposited near neutral pH were thicker than those deposited at high pH. TAZ films were significantly thinner (∼20Å) than BTA films deposited under similar conditions, approaching a self assembled monolayer (SAM). The BTA removal rate for a citrate solution with a pH of 4 was 20Å/min., an order of magnitude lower than that for TMAH-containing solutions. The TAZ removal rate for an oxalate solution with a pH of 4 was 240Å/min., which was twice the removal rate for BTA deposited under similar conditions. An appropriate TAZ solution was found to displace BTA on Cu and leave a hydrophilic, thin (∼20Å) passivating layer of TAZ. Other Cu passivators were also examined but only TAZ protected all Cu crystallographic orientations observed. BTA, 5-aminotetrazole (5-ATA) and 4-carboxybenzotriazole (CBTA) did not protect some Cu crystal orientations, leading to etching of entire grains and increased surface roughness. BTA and CBTA yielded hydrophobic Cu surfaces, leading to surface wetting issues and the potential for watermarks. A new alkaline Cu post-CMP cleaner was developed to remove residues resulting from slurries, regardless of their pH, which utilizes TAZ to displace BTA and protect Cu, significantly lower organic defects, reduce surface roughness, provide a hydrophilic Cu surface, and significantly extend the staging time allowed between the clean process and subsequent wafer processing.

Keywords

CMPmicroelectronicspassivation
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 991: Symposium C – Advances and Challenges in Chemical Mechanical Planarization , 2007 , 0991-C08-01
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Fox, P. G., Lewis, G., and Boden, P. J., “Some Aspects of the Corrosion Inhibition of Copper by Benzotriazole”, Corrosion Science, Vol. 19, pp. 457–467, Pergamon Press, Ltd. (1979).Google Scholar
2. Ogle, I. C. C. and Poling, G. W., “Corrosion Inhibition of Copper with Benzotriazole”, Canadian Metallurgical Quarterly, Vol. 14, pp. 37–46 (1975).Google Scholar
3. Roberts, R. F., “X-Ray Photoelectron Spectroscopic Characterization of Copper Oxide Surfaces Treated with Benzotriazole”, Journal of Electron Spectroscopy and Related Phenomena, Vol. 4, pp. 273–291, Elsevier Scientific Publishing, Amsterdam (1974).Google Scholar
4. Siedle, A. R., Velapoldi, R. A., and Erickson, N., “Surface Formation of Cuprous Benzotriazole”, Inorganic and Nuclear Chemistry Letters, Vol. 15, pp. 33–36, Pergamon Press, Ltd. (1979).Google Scholar
5. Lange's Handbook of Chemistry, 15th ed., p. 8.31, McGraw-Hill, Inc. New York (1999).Google Scholar
6. Huang, C. H., “Corrosion Protection of Copper with Benzotriazole”, Plating and Surface Finishing, pp. 96–100 (June 1986).Google Scholar
7. Notoya, T. and Poling, G. W., “Topographies of Thick Cu-Benzotriazole Films on Copper”, Corrosion – NACE, Vol. 32, No. 6, pp. 216–223 (June 1976).Google Scholar
8. Peters, D. et al. , “Investigation of the Impact of Barrier Slurry Properties on Post-CMP Cleaning Efficiency”, ECS Transactions, Vol. 1, No. 3, pp 357–364 (2005).Google Scholar
9. Peters, D. et al. ,, “Displacement Cleaning: A New Mechanism for Copper Post-CMP Cleaning”, The 2nd PacRim International Conference on Planarization CMP and its Application Technology, pp. 68–72 (November 2005).Google Scholar
10. Peters, D., et al. , “Open Circuit and Galvanostatic Behavior of Copper Oxidized and Reduced in Various Solutions”, Electrochemical Society Proceedings, Vol. 2003–26, pp. 421–425 (2004).Google Scholar
11. Peters, D. et al. ,, “Low Carbon Contamination and Water Mark Free Post-CMP Cleaning of Hydrophobic OSG Dielectric”, Electrochemical Society Proceedings, Vol. 2003–26, pp. 305–311 (2004).Google Scholar
12. Buley, T. et al. ,, “Wet Surface Technologies”, Micro Magazine.com, Oct./Nov. (2005).Google Scholar
13. Petitdidier, S., “Method for the Treatment of Copper Surfaces for the Removal of Carbonaceous Residues”, US patent application 11/187,707.Google Scholar