This study investigates the problem of non-Newtonian liquid evaporation from an impermeable vertical plate in a porous medium under mixed convection conditions. The analysis examines the effects of non-Darcian flow phenomena on the evaporation process and investigates the heat and mass transfer characteristics under a range of flow conditions in the aiding and opposing flow types. The parameters of interest include Rak,non, Pex,non, Pr and Sc. The data required for the calculations include a fixed wall temperature of Tw = 45°C, a free flow temperature of T∞ = 20°C and an air free flow rate of u∞ = 4m/sec and the corresponding humidity of 50% flows over fixed temperature and moist wall.

The results indicate that an increasing buoyancy force enhances the mixing effect and therefore improves the rate of heat transfer, the latent heat flux is the primary mode of heat transfer in evaporation processes and the velocity gradient at the wall increases with an increasing buoyancy effect. Furthermore, the evaporation rate increases with a reducing flow index and an increasing buoyancy effect.

Cervical muscles are crucial in providing the stability of the cervical spine. Many in vitro studies have investigated the relationship between muscle force and stability directly. However, the effects of different muscle dysfunctions or muscle recruitments on cervical spine stability are not yet clear and therefore, worthy of study. A spine testing apparatus with muscle force replication activated by pneumatic cylinders was developed to find the effect of muscles on spinal stability. Seven porcine cervical spines (C2-T1) were used. Three pairs of cervical muscles, including neck flexors (sternocleidomastoid, SCM) and neck extensors (splenius capitis, SPL; semispinalis capitis, SSC), were simulated. The experimental tests included: 1. no muscle recruitment, 2. full muscle recruitments, 3. SCM dysfunction, 4. SPL dysfunction, and 5. SSC dysfunction. The external pure moment in sagittal plane was applied from 0 Nm to 2 Nm to examine the stability/flexibility of specimens. The spinal stability was evaluated by the neutral zone (NZ), the range of motion (ROM), the reduced NZ (R_NZ), and the reduced ROM (R_ROM). Loading responses of C7-T1 disc were also measured. The results of this study showed: The activation of cervical muscles decreased the NZ and ROM. The degree of decrease among different muscle dysfunctions, however, was not significantly different. The SPL dysfunction induced larger anterior shear force, while the SCM dysfunction exclusively induced extension moment. In conclusion, the muscle forces could stabilize the cervical spine, but significant decrease in spinal stability was not found among dysfunctions of different muscles. The SCM and SPL dysfunction may result in abnormal stress at the C7-T1 disc.

The applications of skew plates in the construction of aerospace structures are well known. The critical buckling load and post-buckling strength are two important design parameters of skew composite laminates. In this study, the refined buckling and nonlinear postbuckling solutions of a homogenous isotropic skew plate based on polynomial expansions of various degrees have been examined. Numerical results based on high-order Rayleigh-Ritz solutions are presented for certain type of oblique plates.

In this paper, the cleanroom fire simulation in a semi-conductor factory is investigated by using the commercial computational fluid dynamics (CFD) code. We using three different combustion models in the fire simulation. The combustion models including the volume heat source (VHS) model, the eddy break-up (EBU) model and the presumed probability density function (prePDF) model are considered to predict the cleanroom fire. The turbulence models coupled with different combustion models, while the radiation model is coupled with the turbulent combustion processes. Additionally, the discrete transfer radiation method (DTRM) is used in the global radiation heat exchange. For the fire simulation, the different combustion models are evaluated for their performance and compared with the experimental data from the literature to verify. Thus, these numerical simulations can be adopted as a useful tool to design and optimize the smoke control strategy in cleanroom fire.

This research focuses on the analysis of vibration and noise control of a fuselage. A closed cylindrical shell is chosen as the theoretical model of the fuselage of an aircraft. The noise resulted from propellers is the main source of excitation to the fuselage vibration. The vibration can further induce interior noise within the fuselage. For attenuating the vibration of the fuselage and its accompanying interior noise, several pairs of piezoelectric sheets are attached to the shell. Each piezoelectric pair connected to an appropriate electric circuit can serve as a dynamic absorber. For a better performance, feedback control algorithms are introduced to form active absorbers. The dynamic responses of the composite cylindrical shell and the corresponding interior sound fields are analytically formulated. Numerical results are presented. The active absorbers are proven to yield good effects on vibration and noise reductions. Some parameter studies are also given in this manuscript.

This paper describes the combination of the method of fundamental solutions (MFS) and the dual reciprocity method (DRM) as a meshless numerical method to solve problems of thin plates resting on Winkler foundations under arbitrary loadings, where the DRM is based on the augmented polyharmonic splines constructed by splines and monomials. In the solution procedure, the arbitrary distributed loading is first approximated by the augmented polyharmonic splines (APS) and thus the desired particular solution can be represented by the corresponding analytical particular solutions of the APS. Thereafter, the complementary solution is solved formally by the MFS. In the mathematical derivations, the real coefficient operator in the governing equation is decomposed into two complex coefficient operators. In other words, the solutions obtained by the MFS-DRM are first treated in terms of these complex coefficient operators and then converted to real numbers in suitable ways. Furthermore, the boundary conditions of lateral displacement, slope, normal moment, and effective shear force are all given explicitly for the particular solutions of APS as well as the kernels of MFS. Finally, numerical experiments are carried out to validate these analytical formulas.

Thirty six kinds of chamfered and unchamfered main cutting edge carbide tips were used in turning of high-strength glass-fiber-reinforced plastics (GFRP) materials to study the cutting temperature of tip's surface. The frictional forces and heat generated on elementary cutting tools are calculated by using the measured cutting forces and the theoretical cutting analysis. The heat partition factors between the tip and chip are solved by using the inverse heat transfer analysis, which utilizes temperature on the K type carbide tip's surface measured by infrared as the input. The tip's surface temperature of the carbide is solved by finite element analysis (FEA) and compared with those obtained from experimental measurements. A good agreement demonstrates the accuracy of the proposed model.

This paper aims to investigate the failure mechanism of a shallow foundation on poorly cemented sandstone and to propose an upper bound solution for the bearing capacity of the foundation. A series of laboratory material and load-bearing model tests with specimens made of artificial rock mimic undisturbed natural poorly cemented sandstone.

Based on a series of load-bearing model tests, bearing behavior and progressive failure mechanisms are investigated. It was found that the bearing behavior on poorly cemented sandstone is distinct from the cases on hard rock or on soil, and exhibits both plasticity and brittle characteristics. It is noted that the bearing capacity formulas for a shallow foundation commonly used for soil or hard rock are not appropriate for the case of poorly cemented soft sandstone. Based on the observed failure mechanism, a simplified plastic collapse mechanism is proposed and an upper-bound solution on the basis of a multi-block translation mechanism is formulated. It is shown that the upper bound solution agrees well with the experimental bearing capacity as long as a proper non-associated flow rule is adopted.

A magnetic hydrodynamic (MHD) mixed convection of an incompressible viscoelastic fluid over a stretching sheet with ohmic dissipation is studied. The buoyant effect and the electric number E1 couple with magnetic parameter M to represent the dominance of the ohmic effect are presented in governing equations which is the main contribution by this study. The similarity transformation, the finitedifference method have been used to analyze the present problem. The numerical solutions of the flow velocity distributions, temperature profiles and the important wall unknown values of f″(0) and θ′(0) are carried out.

This paper studied cyclic behavior Sn/3.8Ag/0.7Cu solder with dendritic microstructure. A cyclic damage factor D under constant strain amplitude fatigue tests, was defined by using the reducing rate of maximum cyclic tensile stress σa. The critical cyclic damage DC and it's fatigue initiation life NI were determined very consistently by using separately the experimental σavs. N curves and the percolation theory. The endochronic cyclic damage-coupled viscoplastic theory proposed by the 1st author was used to simulate cyclic stress-strain hysteresis loops with damage under strain amplitude (εa) 0.8% at 298K. The results were in very good agreement with data. Combining the evolution equation of intrinsic damage and the computed cyclic stress-inelastic strain relation, a modified Coffin-Manson relationship was derived. By setting DC = 0.3, it predicted very effectively the NI data under σa from 0.2% to 1.0%.

The scattering of time harmonic plane longitudinal and transverse elastic waves in a composite consisting of randomly distributed identical isotropic spherical inclusions embedded in an isotropic matrix with anisotropic interface layers is examined. The interface region is modeled as a spherically isotropic shell of finite thickness with five independent elastic constants. The Frobenius power series solution method is utilized to deal with the interface anisotropy and the effect of random distribution of particulates in the composite medium is taken into account via a recently developed generalized self-consistent multiple scattering model. Numerical values of phase velocities and attenuations of coherent plane waves as well as the effective elastic constants are obtained for a moderately wide range of frequencies, particle concentrations, and interface anisotropies. The numerical results reveal the significant dependence of phase velocities and effective elastic constants on the interface properties. They show that interface anisotropy can moderately depress the effective phase velocities and the elastic moduli, but leave effective attenuation nearly unaffected, especially at low and intermediate frequencies. Limiting cases are considered and good agreements with recent solutions have been obtained.

In this article the mass and heat transfer between fluid molecule and carbon tube is studied via molecular dynamic simulation based on Lennard-Jones Potentia and Bernner-Tersoff Potential model. Some valve holes are formed by removing different numbers of molecules from flank of (5, 5) armchair carbon tube (the hole area = 17.3 ∼ 116.9Å2). The results indicate that only diffusion behavior is not able to describe the phenomena, otherwise the atom release rate and valve hole size are interdependent. Meanwhile the variation of potential energy barrier, work function, energy gap arose from different valve geometrical size are observed. These variations can influence the dynamic behavior such as flow rate and velocity by molecule penetration.

A Lagrangian style vortex simulation technique is used to study the flow fields past a stationary flat plate at various angles of attack in the range 1° to 90°. Time mean values of oscillating lift and drag coefficients, and the Strouhal number versus angle of attack are computed and compared with experimental results. Time-mean and root-mean-square values of stream-wise and transverse velocities in the wake region are also calculated. Self-similar defect velocity distribution is obtained far downstream. Owing to the interaction of free shear layers, highly root-mean-square values of velocities appear at the downstream vertex of the triangular low velocity region, which exits behind an inclined flat plate.

By considering the total transverse displacement of a sandwich plate as the sum of the displacement due to bending of the plate and that due to shear deformation of the core, a high precision higher order triangular plate element is developed for the nonlinear panel flutter analysis of thermally buckled sandwich plates. Von Karman large deformation assumptions and quasi-steady aerodynamic theory are employed for the analysis. Newmark numerical time integration method is applied to solve the nonlinear governing equations in time domain. Results show that temperature will increase both the maximum displacement and motion speed of the plate. But the maximum displacement and velocity of the plate will not vary much with the aerodynamic pressure. Buckle pattern change phenomenon occurred in some specific case will increase the flutter boundary and change the flutter motion type of the plate. Temperature gradient increases the overall stiffness of the plate, which in turn stabilizes the sandwich panel and increases the flutter boundary of the plate.

Multicomponent composite materials comprised of a dispersed phase suspended in a matrix material are important in a wide variety of scientific and engineering applications including electronic encapsulation, functionally graded materials, and fiber-reinforced structural components among others. Modelling of this class of composites is typically performed using an effective property approach. This approach presumes that the characteristic dimension of the dispersed phase elements is small in comparison to the characteristic length scale of the physical problem under consideration. However, it is not possible to predict a third effective elastic property based on two independent effective elastic properties as it is for homogeneous elastic isotropic materials. Therefore, a macroscale simulation based on an effective Young's modulus and Poisson ratio may yield poor results for a material subjected to shear loading since there is a potentially incorrect presumed effective shear modulus for the simulation. In the current research, boundary element simulations are performed for mesoscopic samples of composite materials to determine effective bulk moduli, shear moduli, Young's moduli, and Poisson ratios. From these analyses, limitations in the effective property approach can be examined.

Since a conventional petrographic analysis does not allow a systematic and detailed study on how the microscopic factors affect the macroscopic behavior of inter-layered rocks, this research adopted a numerical model, the bonded particle model, to explore the micro-mechanisms associated with the strength and stiffness of inter-layered rocks. The model was first calibrated by comparing the simulations to the actual behavior until they tally with each other. Following, the microscopic factors, including the bond strength, the bond stiffness, type of bonds and friction of particles and type of bond stiffness, are varied to study their influences. As expected, the bond strength and the bond stiffness are found to have a direct and significant influence on the macroscopic uniaxial compressive strength and stiffness, respectively. Furthermore, close observations on the breaking of bonds during the loading process reveal interesting phenomena, including the transition of shear/normal bond breaking, the type of internal fracture and the factors controlling internal failure, etc. These phenomena enlighten the interpretations about the micromechanisms accounting for the macroscopic strength and stiffness of inter-layered rocks.

This paper deals with the linear dynamic responses of beams with a flexible support under a moving load with a constant speed. The entire system is modeled as a two-span beam and each span of the continuous beams is assumed to obey the Euler-Bernoulli beam theory. Considering the compatibility requirements on the flexible constraint, the relationships between two segments can be obtained. By using a transfer matrix method, the characteristic equation of the entire system can then be determined. The forced responses of the system under a moving load can then be obtained through modal expansion theory. Some numerical results are presented to the effects of support stiffness and the different speeds of the moving load.

The development of elbow arthroplasties has significantly improved the quality of life for many patients suffering from disabling elbow disorders. However, the high complication rate such as loosening and instability limits the long term use of total elbow replacement (TER). In the present study, biomechanical analyses on patients with unilateral nonconstrained (Souter-Strathclyde) and semiconstrained (Coonard-Morrey) TER subjects were performed to investigate differences of their motion patterns under unloaded and loaded conditions. In a biomechanical laboratory, each subject performed vertical and horizontal elbow flexion/extension first without and then with external loading (5 lb). The kinematic data were measured using 3D motion analysis system and the motion axis of the elbow was calculated by a well-defined mathematic model. During these tests, the upperarm was fixed with a special fixation device and their forearms fully supinated. The elbow motion patterns of the affected sides were compared with those of the normal sides and between different conditions. The results revealed that the elbows moved about a relatively fixed axis both in the semiconstrained and nonconstrained groups in the vertical flexion/extension with or without external loading, compatible with the normal elbows. However, the nonconstrained elbows were less stable during horizontal flexion/externsion motion with or without external loading and the elbow axis moved significantly, indicating of less stability. We conclude that this methodology of elbow motion analysis is acceptable and can be widely recommended for total elbow study. Moreover, the nonconstrained TER is less stable than the semiconstrained TER during the horizontal movement, which was compatible with previous clinical results. The patients with nonconstrained TER are suggested to avoid using their elbows in horizontal motion, especially in loaded conditions.

A model adopting the surface capturing method is developed for the simulation of dam-break flows by solving the Navier-Stokes equations of weakly compressible and variable density flows in open channels. Due to the characteristics of weakly compressible flow equations, a compressibility parameter describing the compressibility of fluid is determined to obtain the time-accurate flow fields in both liquid and gas regions simultaneously. Accordingly, the location of free surface can be captured as a discontinuity of the density field for dam-break flow simulations. The numerical algorithm in the proposed method is based on the framework of the finite volume method for discretization in space. To deal with the discontinuity property of fluid density near the free surface, the TVD-MUSCL scheme is adopted to overcome numerical oscillations and dissipation. For discretization in time, the explicit 4-stage Runge-Kutta scheme is employed in the model. Finally, several typical dam-break flow problems in open channel are simulated to demonstrate the validation and applicability of the proposed model.

The aim of this paper is to investigate the mechanism of the fission process and the flow field of N-waves in the near-shore region. From the elaborate experimental analysis, a subsequence of a second soliton released during shoaling reigon is identified to realize the further evolution of N-waves over a sloping beach, in comparison with the non-fission case. The fission index is indicated by a dimensionless factor A0/d0, which is used to describe the nonlinearity as well. It is known that the reflecting wave and the breaking effect could easily initiate another soliton, especially for strong nonlinear case. A series of experiments were conducted in a super wave flume (300m × 5m × 5.2m) at Tainan Hydraulics Laboratory (THL), National Cheng Kung University (NCKU). The entire evolution of the leading and second solitons and the generation mechanism for the third soliton would be discussed in this paper.