The aim of the present study was to examine effects of black liquor-montmorillonite (BL-Mnt) complexes on the mechanical and thermal properties of epichlorohydrin rubber. Considering the stability effect of lignin and the barrier property of clay minerals, a significant enhancement of thermo-oxidative aging properties of ECO/BL-Mnt composites was expected. Poly (epichlorohydrin-co-ethylene oxide) (ECO) composites filled with BL-Mnt complex were prepared by mechanical mixing on a two-roll mill. The ECO/BL-Mnt composites were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). Both XRD and TEM data showed that the filler particles were well dispersed throughout the ECO/BL-Mnt composites. The tensile strength, elongation at break, and 100% modulus of the rubber composite were 14.0 MPa, 457%, and 3.9 MPa, respectively, at a 50% loading of BL-Mnt. The retention of tensile strength was 99% after thermal oxidative aging in an air-circulating oven for 72 h at 100°C. Evidence indicated that ECO/BL-Mnt composites with good mechanical properties and thermo-oxidative aging properties were obtained.

The present study determined the mineralogy and thermal properties of kaolin from Acoculco (Puebla), at the eastern Trans-Mexican Volcanic Belt and compared it with the nearby deposits of Agua Blanca (Hidalgo) and Huayacocotla (Veracruz). The mineralogy of the kaolins was determined by X-ray diffraction, infrared spectroscopy and scanning electron microscopy. Thermal behaviour was studied by differential thermal analysis, dilatometry and hot-stage microscopy. The Acoculco deposit is composed mainly of kaolinite and SiO2 minerals. In the case of Agua Blanca and Huayacocotla, alunite is abundant in places and minor anatase is also present locally. The Acoculco kaolins are Fe-poor and relatively rich in some potentially toxic elements (Zr, Sb, Pb). They undergo a relatively small amount of shrinkage (∼3–4 vol.%), during firing at 20–1300°C and cooling down to 20°C, except when >10 wt.% alunite is present. These kaolins are a suitable raw material for the ceramics industry. Other applications (pharmaceuticals, cosmetics) would require an enrichment process to eliminate impurities such as Fe oxides.

Thirty clay samples collected from three hills in Koutaba (west Cameroon) were characterized in order to evaluate their potential use as raw materials for ceramics. After preliminary mineralogical identification by X-ray diffraction, three representative samples from the three different hills, referred to hereafter as K1M, K2M and K3M, were selected for further investigation by X-ray fluorescence, plasticity, granularity and thermogravimetric analysis. The main clay minerals are kaolinite (32–51%) and illite (up to 12%). Additional major phases are quartz (32–52%), goethite (6–7%) and feldspars (0–4%). The chemical composition showed variable amounts of SiO2 (60–72%), Al2O3 (15–20%) and Fe2O3 (1–9%), in accordance with the quartz abundance in all of the samples studied. The particle-size distribution showed a large proportion of silty fraction (64–88%) with moderate sandy (9–19%) and clayey fractions ( < 5% for K2M, 12% for K1M and 20% for K3M). All of the clays showed moderate plasticity-index values (8–11%). Because of these characteristics, K1M and K3M may be suitable for use in common bricks and hollow ceramic products. Sieving or the addition of ball clays is recommended to increase the plasticity of sample K2M for use in common bricks.

We present the results of a mixed-space approach, based on first-principles calculations, to investigate phonon dispersions and thermal properties of Mg2Si and Mg2Sn, including the bulk modulus, Grüneisen parameter, heat capacity, and Debye temperature. It is shown that good agreements are obtained between the calculated results and available experimental data for both phonon dispersions and thermal properties. The phonon dispersions are accurately calculated compared with experimental data due to the high-quality description of LO–TO splitting and transverse acoustic branches along the Γ-K-X symmetry line. We also calculate the heat capacity CP and Debye temperature of Mg2Si1−xSnx alloys (x = 0.375, 0.5, 0.625, 0.875). The CP values at high temperature range from 0.5 to 0.7 J/g/K and ΘD values at room temperature from 332 to 384 K as the Sn content decreases from 0.875 to 0.375.

The piezoelectric β-phase of poly(vinylidene fluoride) (PVDF) has been synthesized through solution route in presence of varying percentage of silicon carbide (SiC). Various measurements were conducted to analyze the effect of SiC addition on structural, mechanical, and dielectric properties, as also the properties affecting hydrophilicity and morphology of PVDF. The x-ray diffraction, Fourier transform infrared spectroscopic and differential scanning calorimetry analyses confirm the presence of β-phase of PVDF on addition of SiC. The Young’s modulus of the composites increases as compared with pristine PVDF. The hydrophilic nature of the composites improves with increasing SiC content. Dielectric constant increases in composites, especially at lower frequency range and the relaxation pattern in the crystalline phase changes significantly causing reduction of relaxation frequency with increasing SiC concentration.

The effects of distinct properties during phase change on mass, momentum, energy, species, and magnetic field intensity transport in workpieces and electrodes in the course of heating, melting, cooling and freezing periods in AC (alternative current) resistance spot welding are realistically and extensively investigated. Resistance spot welding has been widely used in joining thin workpieces due to its light weight and easy manufacturing. This study accounts for electromagnetic force, heat generations at the electrode-workpiece interface and faying surface between workpieces, and dynamic electrical resistance taking the sum of temperature-dependent bulk resistance of the workpieces and contact resistances at the faying surface and electrode-workpiece interface. The contact resistance is a function of hardness, temperature, electrode force, and surface condition. Instead of dealing with specific materials, this work is a general dimensionless investigation of resistance spot welding of materials with different specific heat and thermal conductivity ratios subject to realistic working parameters. The computed results show that nugget formation is delayed and heat transfer is reduced by increasing solid-to-liquid thermal conductivity and liquid-to-solid specific heat ratio. The corresponding thermal fields and flow patterns are also presented.

The effect of superheating and substrate morphology on heat exchange at the melt-solid interface was studied. An experimental device was set up to yield a unidirectional heat flow from the Sn-Pb bath to the lubricated steel substrate and the heat transfer resistance was evaluated from the thickness of the solidified material at a fixed time. A higher solidification efficiency was obtained with moderate superheating, and also with a proper choice of surface topography and lubricant.

Although adhesives, particularly those based on epoxy resins, are finding increasing use in structural applications, their utilization at elevated temperature (>150°C) has been limited by their relatively poor thermal and thermo-oxidative stability. As a result, significant effort has been directed in recent years toward the development of polymers exhibiting increased thermal resistance. Although a wealth of research conducted over several decades has resulted in a myriad of polymer types exhibiting, in some cases, impressive high-temperature performance, many systems have demonstrated poor processability Thus, much emphasis has been placed on developing high-temperature performance while providing processability characteristics that are similar, if not identical, to epoxies. This article considers the various approaches that have been shown to offer such dual capabilities. In addition, the results of various studies undertaken to investigate the effects of elevated temperature on the strength and fatigue resistance of bonded joints are reported.