This paper presents a broadband circularly polarized (CP) antenna array for millimeter-wave applications, and the antenna array has the advantages of wide impedance bandwidth (IBW), novel CP design, and low profile. The antenna unit consists of a two-layer substrate and two pairs of magnetoelectric dipoles. Stepped microstrip lines coupled by rectangular slits form a feeder network for easy integration. The axial ratio bandwidth (ARBW) is extended because a pair of parasitic patches is loaded and an elliptical perturbation is added. The simulation results show that the antenna has an ARBW of 18.6% (26.4–31.9 GHz) and an IBW of 45.5% (20.6–32.7 GHz), with a gain greater than 7.11 dBic in the IBW. To improve the gain of the antenna, a 2 × 2 antenna array is designed, fabricated, and measured. The measured results show that the array has an ARBW of 16.6% (26.42–31.21 GHz), an IBW of 41.6% (22.28–33.97 GHz), a peak gain of 13.89 dBic in the IBW, the cross-polarization levels in the xoz-plane and yoz-plane are above 20 dB, and a radiation efficiency greater than 89%.

The major component for the effective functioning of airborne unmanned aerial vehicles (UAVs) is an antenna. The unified integration of an antenna with UAVs without disturbing the other components of UAVs, compact size, thin, and wideband antennas are preferred. Based on these prerequisites, a low-profile and a wideband antenna is presented for autonomous UAVs for C-band applications. The antenna is designed on an extremely thin substrate of size 0.01λ0 without compromising the antenna's broad bandwidth. The antenna structure comprises a corrugated U-shaped patch, a few parasitic patches along with the partial ground. Initially, only a single mode was excited using a U-shaped patch, then further on introducing a few more parasitic patches along with corrugations in a U-shaped patch other modes were also coupled leading to enhancement in the bandwidth of the antenna. The proposed antenna along with a 2 × 2 quad-port multiple input, multiple output (MIMO) antenna is designed and fabricated. The measured results are found to be in good agreement with the simulated results. A broad bandwidth of 74.5% (4.1–9.0 GHz) with 5.02 dBi peak gain at 6.6 GHz is exhibited by the fabricated MIMO antenna. Thus, the designed antenna proves to be an effective candidate for UAV-based C-band applications.

This paper presents a 60 GHz connected slots linear-phased array feeding a high-gain semi-symmetric lens antenna. This design provides high gain, broadband, and beam-steering capabilities for gigabit rate access and backhaul communications. The connected slots antenna array (CSAA) is excited at 16× equidistant points which not only yields spatial power combining but also allows the progressive phase changes to steer the beam in ±45° in azimuth plane. To characterize the CSAA-fed lens antenna, four different power splitters are fabricated which steer the main beam in 0, 15, 30, and 45°. The lens is designed in a way to overcome the scan loss and get comparatively higher gain when beam is steered away from the broadside. The measured results show 25.4 dBi maximum gain with 3 dB gain bandwidth covering the full band 57–66 GHz whereas 3 dB beam-steering range is ±45° for all frequencies. Besides, the half power beamwidth is 6 and 10° in elevation (E-plane) and azimuth plane (H-plane), respectively.

Substrate-integrated waveguide (SIW) technology has recently drawn attention to its benefits in the microwave field, such as integration in planar microwave circuits, low manufacturing cost, and high-quality factor compared to other technologies. In this paper, a broadband and high gain SIW cavity-backed L-shaped slot antenna structure has been designed and made for X-band applications. Three pairs of L-shaped half-wave resonators are placed on the lower wall of the cavity (backed-slots) to further expand bandwidth and improve gain. The final antenna designed operates on a band ranging from 9.4 to 10.5 GHz with a bandwidth of 11%. Moreover, the gain reaches a value of 9.5 dBi. The final antenna is realized on a Rogers RT/Duroid 5870 substrate. The gain, the reflection coefficient, and the radiation patterns are measured and compared to the EM simulation results and a very good agreement is obtained. The proposed cavity-backed L-shaped slot antenna gives a good compromise between a high gain and a large bandwidth.

In this paper, the antenna reconfigurable technology is used to redesign a whip antenna in different sub-bands of high frequency (HF). According to the electrical characteristics of the antenna, on the one hand, two different radiation whip heights are designed to solve the problem of pattern up-warping in the high-frequency band; on the other hand, a common upper loading network and several different adjusting inductors and matching networks are designed for each sub-band to achieve high gain and efficiency when keeping good voltage standing wave ratio (VSWR) characteristics. Five sub-bands of the 10-m HF whip antenna are reconfigured through the actual selection of radiation height, adjusting inductance, and matching network by radio frequency (RF) switch. The antenna load and matching network are optimized by grasshopper optimization algorithm (GOA), and integrated into the antenna body by using the printed circuit technology. The scaled prototype of 1 m frequency reconfigurable antenna is manufactured and tested, which shows that the VSWR is all <3 with an average value of 2.14; the gain is all >−2.5 dB with an average value of 3.90 dB; the efficiency is all >18.2% with an average value of 71.59%, and the patterns all keep horizontal omnidirectional without the phenomenon of up-warping.

A flexible broadband antenna with high radiation efficiency for the Internet of Things (IoT) applications is presented. The design is based on a U-shaped and a triangular-shaped radiator with two tuning stubs. A 50 Ω coplanar waveguide (CPW) transmission line is employed to feed the antenna. The proposed antenna is fabricated on a flexible substrate from a composite synthesized by mixing natural rubber with SiO2 as a filler. The radiating elements, along with the CPW, are built using a highly conductive woven fabric. Results show that the antenna has a simulated and measured impedance bandwidth of 0.856–2.513 GHz and covers the most commonly used wireless communication standards and technologies for IoT applications. The radiation efficiency of the antenna reaches over 75% throughout the operating frequency band with satisfactory radiation patterns and gain. The flexible antenna was also tested under bending conditions. The presented results demonstrate that bending has a minor effect on the antenna performance within the target frequency range. The measured results show a good agreement with simulations.

This paper presents the behavior of three iterations of a coplanar waveguide fed CANTOR Set fractal antenna. This kind of antennas allows having a broadband behavior and important gains. Also, the setup of slots allows having more lower resonant frequencies and therefore designing miniaturized antennas with good performances. The proposed antennas are suitable for 2.5/3.3/5/5.5 GHz worldwide interoperability for microwave access and for 2.4–2.5/4.9–5.9 GHz wireless local area networks applications. The simulations were performed in FEKO 6.3. The measurements were performed with Vector Network Analyzer HP 8719C.

This paper presents a multiple-input and multiple-output dual-element planar inverted-F antenna (PIFA) array for broadband operation covering the HIgh PERformance radio Local Area Network/2 (5.2 GHz/5.6 GHz), Wireless Local Area Network (5.2 GHz/5.8 GHz), and the Worldwide Interoperability for Microwave Access (5.5 GHz) bands for the compact wireless communication devices. The antenna dimension is reduced substantially with a miniature ground plane. The PIFA array provides a large bandwidth (670 MHz) and a high isolation between its ports less than −26 dB. The proposed antenna has been analyzed and designed with Ansoft HFSS v.11. Then a prototype was fabricated and tested for its performance in terms of bandwidth, S-parameters, and radiation pattern. A parametric study is made to analyze the effect of different PIFA parameters on the operating frequency and the S-parameters. The diversity performances are evaluated using computer simulation technology microwave studio (CSTMWS). The broadband performance and the high isolation are achieved in both simulation and measurement.