In this work, three successive filter models based on defected ground structure (DGS) techniques are designed, fabricated, and tested to be utilized for different wireless applications. The filters are printed on a RO5880 substrate of an overall size of 22 × 11 × 0.8 mm3. Three DGSs are etched from the ground plane to achieve the suggested band stop features for all frequencies above 10 GHz. The first model is a low-pass filter that succeeded to pass all frequencies below 10 GHz, the second model is a bandpass filter that operated at 4.5 and 9 GHz after using a pair of interdigital capacitors, and the third model covered all ultra-wideband frequency range when a pair of lumped capacitors is utilized instead of the interdigital capacitors. Good consistency between simulated and measured outcomes is achieved for each of the three filters confirming their suitability to be embedded in small-sized wireless devices.

The μ-negative metamaterial (MNG) two-element MIMO antenna design was proposed in this article for WiMAX (2.5–2.8 GHz), WLAN (3.2–5.9 GHz), and ITU band (8.15−8.25 GHz) applications. The first design of the MIMO antenna operates at 2.7 and 4.9 GHz frequencies. In order to reduce the mutual coupling, a defective ground structure is used. For further isolation improvement, an MNG unit cell is placed in between the two radiating elements at a distance of 10 mm. The designed antenna elements have better than −23 dB coupling isolation between the two radiating elements. Moreover, with MNG an additional frequency of 8.2 GHz is obtained, which is useful for ITU band applications. The proposed antenna bandwidth is expanded by 19% in the lower operational band, 20% in the second operational band, and 32% in the higher frequency band with the MNG unit cell. From the analysis, the proposed antenna is suitable for WiMAX/WLAN/ITU band applications because of its low enveloped correlation coefficient, and highest directive gain and low mutual coupling between the radiating components. The proposed antenna was simulated, fabricated, and measured with the help of the Schwarz ZVL vector network analyzer and anechoic chamber. Both measured and simulated results are highly accurate and highly recommended for WiMAX/WLAN/ITU bands.

This paper presents a novel compact dual-band printed antenna with an omnidirectional radiation pattern for 5G WLAN. The antenna element comprises a star-shaped patch with six disc-shaped elements at the top and a defected ground structure at the bottom, having a radius of 3.77 mm for both. The proper feeding point and alignment with its element parameters help to achieve good impedance matching. The proposed antenna has a single center feed, a low profile, and a straightforward compact structure without any feeding complexity. A high reception fidelity antenna with comparable bandwidth and moderate gain is presented. The prototype radiator was printed on a 4 mm radius and a 1.6 mm thick dielectric substrate (Rogers RT/Duroid 5880), with a dielectric constant of 2.2. The designed antenna is fabricated and measured to validate the simulation result. The measured impedance bandwidth of 1.3 GHz (27.5–28.8 GHz) and 2.2 GHz (32.45–34.65 GHz) with a respective measured gain of 1.1 and 3.2 dBi are achieved at 28 and 34 GHz. The simulated radiation efficiency of above 95% is achieved for both bands. A good agreement between simulated and measured results of the proposed work shows that the proposed antenna is suitable for 5G short-range WLAN communications.

This article introduces a cylindrical dielectric resonator antenna (CDRA) fed with a rhombic ring-shaped tapered feed for Multiple-Input-Multiple-Output (MIMO) applications. The proposed hybrid MIMO CDRA resonates at four frequency bands 2.5, 5.09, 6.8, and 9.0 GHz with isolation levels of 22, 34.22, 30.55, and 18.55 dB. Isolation enhancements are achieved by introducing “L” shaped slots on the partial ground plane. Parametric analysis is performed to validate the optimized dimensions of the tapered feed without and with DRA and defected ground structure. Diversity performance is examined by using envelope correlation coefficient and diversity gain. The proposed antenna operates in the S, C, and X-bands and is suitable for RF communication mobile broadband services, Wi-Fi, radar, and satellite applications. Good agreement is observed between simulated and measured results.

In this paper, a three layered stacked circularly polarized rectangular dual band microstrip antenna with a defected ground structure (DGS) and a feed network with stub (showing dual wideband characteristic) is designed, fabricated, and tested for WLAN, Zig bee, Wi-Max, and IMT band applications. The proposed antenna is fabricated on an FR4 substrate with dielectric constant (εr) of 4.4; tanδ of 0.0024 and a height of 1.57 mm.The antenna has a surface area of 4.8 × 4.1 cm2 and a total height of 5.1 mm. The designed antenna covers two wireless bands from 2.39 to 2.64GHz and 3.39–3.76 GHZ with impedance bandwidths (VSWR < 2) of 250 MHz (9% bandwidth centered at 2.515 GHz) and 370 MHz (10% bandwidth centered at 3.57 GHz), respectively. This antenna is capable of covering IEEE 802.11b/g/n standards of WLAN from 2.4 to 2.485 GHz, bluetooth applications from 2.4 to 2.483 GHz, ZigBee applications from 2.4 to 2.485 GHz, IEEE 802.16/ Wi-MaX applications from 3.4 to 3.69 GHz and international mobile telecommunications (IMT) band from 3.4 to 3.6 GHz. As the antenna is circularly polarized, the misalignment of the receiver with transmitter does not affect the performance of the system. The antenna designing was done using CST MWS V'10 and the prototype of the designed antenna was tested for the validation of S11 (dB) and gain results against the simulated ones experimentally. The proposed antenna shows a gain of 4.08 dBi at 2.5 GHz and a gain of 5.024 dBi at 3.51 GHz.

A design of low mutual coupling between two microstrip patch antennas for multi input multi output antenna is presented. The two antenna elements operate at 5.8 GHz for wireless applications. The reduction of mutual coupling between the antenna elements is achieved by using a defected ground structure (DGS). The DGS is inserted between the microstrip patch antenna elements to limit the surface waves between them. The separation between the edges of the two elements has been achieved to be only 0.058λ0. The analysis of the correlation coefficient, diversity gain and total active reflection coefficient is presented to validate the performance of the multiple-input–multiple-output (MIMO) antenna. The isolation of the proposed MIMO antenna is 28 dB at 5.8 GHz and the envelope correlation equals 0.003. Owing to these good performances each antenna can operate almost independently. A good agreement is achieved between the simulated and the measured results.

This paper presents a close but a beginner's perspective and a comprehensive review of microstrip filters with defected ground structure (DGS). The concept of DGS is inspired by photonic/electromagnetic bandgap structures (EBG/PBG) and metamaterials that are employed in microwave components to achieve a variety of performance enhancement features. Modeling of DGS and metamaterials as an L-C equivalent lumped circuit is much simpler in comparison with complex EBGs/PBGs. In this review, we have given a detailed account of the microstrip filters using DGS.