Hostname: page-component-78c5997874-m6dg7 Total loading time: 0 Render date: 2024-11-06T04:23:19.318Z Has data issue: false hasContentIssue false
  • English
  • Français

Analysis of Preferred Orientations in Linear Friction Welded (LFW) Aluminium Alloy Specimens using “One-shot” Multi-element Energy Dispersive Synchrotron X-ray Diffraction

Published online by Cambridge University Press:  14 November 2013

M.Y. Xie ,
T.S. Jun ,
A.M. Korsunsky  and
M. Drakopoulos
M.Y. Xie*
Affiliation:
University Oxford, Department Engineering Science, Oxford OX1 3PJ, England
T.S. Jun
Affiliation:
POSCO, Welding & Joining Research Group, Pohang 790300, Gyeongbuk, South Korea
A.M. Korsunsky
Affiliation:
University Oxford, Department Engineering Science, Oxford OX1 3PJ, England
M. Drakopoulos
Affiliation:
Diamond Light Source, JEEP Beamline 112, Didcot OX11 0DE, Oxon, England
*
E-mail: [email protected]
Get access Rights & Permissions [Opens in a new window]

Abstract

Linear Friction Welding (LFW) has tremendous potential for joining components from similar and dissimilar materials, avoiding material melting and introducing minimal distortion and only moderate levels of residual stress. However, the significant amount of attendant shear introduces preferred crystal orientations that have not yet been well studied. The “one-shot” approach to the interpretation of multi-element energy-dispersive X-ray powder diffraction data allows preferred orientation analysis without any sample preparation (cutting or polishing) or sample rotation. The key step for texture analysis by X-ray powder diffraction is the derivation of the orientation distribution function (ODF) from experimental data. Matlab toolbox “MTEX” provides a powerful function “calcODF” based on the harmonics method for this purpose. In the study reported in this paper, energy dispersive X-ray diffraction patterns were collected using the “horseshoe” multi-element energy-dispersive Ge detector installed on the JEEP beamline at Diamond Light Source. A single exposure was used for each gauge volume of interest, and a line was scanned across an Aluminum 2024 alloy LFW sample. The patterns were converted into raw pole figures through single peak fitting and equal area projection. The ODF calculation was performed based on these pole figures using Matlab toolbox “MTEX”. As a result, full pole figures obtained after ODF calculation were obtained. These are presented and discussed. The results show that the thermal-mechanical processes that occur during the LFW process lead to significant modification of the orientation distribution, but cause only moderate changes in the texture index.

Keywords

energy dispersive X-ray diffractiontexturelinear friction welding
Type
Technical Articles
Information
Powder Diffraction , Volume 28 , Supplement S2 , September 2013 , pp. S327 - S332
Copyright
Copyright © International Centre for Diffraction Data 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Bhamji, I., Preuss, M., Most, R. J., Threadgill, P. L. and Addison, A. C. (2012). “Linear friction welding of aluminium to magnesium.” Sci. Technol. Weld. Joining 17(5), 368–374.CrossRefGoogle Scholar
Bhamji, I., Preuss, M., Threadgill, P. L. and Addison, A. C. (2011). “Solid state joining of metals by linear friction welding: a literature review.” Mater. Sci. Technol. 27(1), 2–12.Google Scholar
Bollinger, C., Merkel, S. and Raterron, P. (2012). “In situ quantitative analysis of stress and texture development in forsterite aggregates deformed at 6 GPa and 1373 K.” J. Appl. Crystallogr. 45(2), 263–271.CrossRefGoogle Scholar
Hielscher, R. and Schaeben, H. (2008). “A novel pole figure inversion method: specification of the MTEX algorithm.” J. Appl. Crystallogr. 41(6), 1024–1037.Google Scholar
Kocks, U. F., Tomé, C. N., Wenk, H.-R. and Mecking, H. (1998). Texture and anisotropy : preferred orientations in polycrystals and their effect on materials properties (Cambridge University Press, Cambridge, U.K.).Google Scholar
Romero, J., Attallah, M. M., Preuss, M., Karadge, M. and Bray, S. E. (2009). “Effect of the forging pressure on the microstructure and residual stress development in Ti–6Al–4V linear friction welds.” Acta Mater. 57(18), 5582–5592.Google Scholar
Wenk, H.-R. and Grigull, S. (2003). “Synchrotron texture analysis with area detectors.” Journal of Applied Crystallography 36(4), 1040–1049.CrossRefGoogle Scholar