Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-25T17:50:50.064Z Has data issue: false hasContentIssue false
  • English
  • Français

Further Investigations of the Microstructural Mechanism of Electromigration Failure in Al-Cu Lines with Quasi-Bamboo Microstructures

Published online by Cambridge University Press:  15 February 2011

S. H. Kang ,
F. Y. Génin ,
C. Kim  and
J. W. Morris
S. H. Kang
Affiliation:
Center for Advanced Materials, Lawrence Berkeley National Laboratory and the Department of Materials Science and Engineering, University of California, Berkeley, CA 94720
F. Y. Génin
Affiliation:
Chemistry and Materials Science, Lawrence Livermore National Laboratory, Livermore, CA 94550
C. Kim
Affiliation:
Center for Advanced Materials, Lawrence Berkeley National Laboratory and the Department of Materials Science and Engineering, University of California, Berkeley, CA 94720
J. W. Morris
Affiliation:
Center for Advanced Materials, Lawrence Berkeley National Laboratory and the Department of Materials Science and Engineering, University of California, Berkeley, CA 94720
Get access

Abstract

Thin-film Al-2Cu conducting lines with “quasi-bamboo” microstructures were investigated to understand the microstructural mechanism of electromigration failure. Both conventional test structures and electron-transparent lines fabricated on silicon nitride windows were utilized to identify the “weakest” polygranular segments. Even when the current density was reduced to 0.75 MA/cm2 and the segment length was on the order of a few microns, failure occurs at the upstream termination of the longest polygranular segment in the line, at a time that decreases exponentially with the segment length. There is no apparent “Blech length” in quasi-bamboo Al- Cu lines; the longest segments are the failure sites, and their lifetime decreases with segment length in a regular way, even when the longest segments are only a few microns in length. It follows (and is observed) that the time-to-failure distribution of a group of lines is fixed by the distribution of the longest polygranular segments within them. This distribution can be effectively controlled by post-pattern annealing, which can refine the quasi-bamboo structure so that the longest polygranular segments are short and the distribution of longest polygranular segment lengths is narrow. Consequently, post pattern annealing is a very effective method for improving reliability by increasing the time to first failure.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 428: Symposium L – Materials Reliability in Microelectronics VI , 1996 , 255
Copyright
Copyright © Materials Research Society 1996

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Kinsbron, E., Appl. Phys. Lett. 36, 968 (1980).Google Scholar
2. Arzt, E. and Nix, W. D., J. Mater. Res. 6, 731 (1991).Google Scholar
3. Kim, C. and Morris, J. W. Jr., J. Appl. Phys. 73, 4885 (1993).Google Scholar
4. Thompson, C. V. and Kahn, H., J. Electron. Mater. 22, 581 (1993).Google Scholar
5. Korhonen, M. A., Borgesen, P., Brown, D. D., and Lee, C.-Y., J. Appl. Phys. 74, 4995 (1993).Google Scholar
6. Lloyd, J. R., in Materials Reliability in Microelectronics IV, edited by P., Borgesen, Coburn, J. C., Sanchez, J. E. Jr., Rodbell, K. P., and Filter, W. F. (Mater. Res. Soc. Proc. 338, Pittsburgh, PA, 1994) pp. 367–372.Google Scholar
7. Marieb, T., Flinn, P., Bravman, J. C., Gardner, D., and Madden, M., J. Appl. Phys. 78, 1026 (1995).Google Scholar
8. Kang, S. H., Kim, C., Morris, J. W. Jr., and Gdnin, F. Y., J. Appl. Phys., in press.Google Scholar
9. Riege, S. P., Hunt, A. W., and Prybyla, J. A., in Materials Reliability in Microelectronics V, edited by Oates, A. S., Filter, W. F., R., Rosenberg, Greer, A. L., and K., Gadepally (Mater. Res. Soc. Proc. 391, Pittsburgh, PA, 1995) pp. 249–258.Google Scholar
10. Shaw, T. M., Hu, C.-K., Lee, K. Y., and Rosenberg, R., Appl. Phys. Lett. 67, 2296 (1995).Google Scholar
11. Kang, S. H., Kim, C., Gdnin, F. Y., and Morris, J. W. Jr., in Materials Reliability in Microelectronics V, edited by Oates, A. S., Filter, W. F., Rosenberg, R., Greer, A. L., and Gadepally, K. (Mater. Res. Soc. Proc. 391, Pittsburgh, PA, 1995) pp. 385–390.Google Scholar
12. Lloyd, J. R., ibid., pp. 231–242.Google Scholar