Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-26T22:37:34.541Z Has data issue: false hasContentIssue false
  • English
  • Français

Creep testing of thick-wall copper electron beam and friction stir welds

Published online by Cambridge University Press:  17 March 2011

Henrik C. M. Andersson ,
Facredin Seitisleam  and
Rolf Sandstr
Henrik C. M. Andersson
Affiliation:
Swedish Institute for Metals Research Drottning Kristinas v. 48 S-114 28 Stockholm, SWEDEN
Facredin Seitisleam
Affiliation:
Swedish Institute for Metals Research Drottning Kristinas v. 48 S-114 28 Stockholm, SWEDEN
Rolf Sandstr
Affiliation:
Swedish Institute for Metals Research Drottning Kristinas v. 48 S-114 28 Stockholm, SWEDEN
Get access

Abstract

Abstract:Thick section copper canisters are planned to be used as a corrosion protection of nuclear waste disposal containers for long term underground deposal in Sweden. The copper canisters will have the top and possibly the bottom lid welded to the canister walls using electron beam or friction stir welding. Due to the high external hydrostatic pressure and the relatively high temperature of the waste during the first one hundred years the copper will creep. The creep process will close the manufacturing gap between the cast iron container and the copper canister. The creep ductility must be sufficient to avoid cracking of the weld.

Specimens cut from the friction stir welds and the electron beam welds have been creep tested at temperatures ranging from 75 to 175 °C. Cross-weld specimens were used for both friction stir and electron beam welds. Weld metal, heat affected zone and base metal were also studied for friction stir welds. The results for the electron beam welds show that the main creep deformation is concentrated to the weld metal where the failure takes place. Weld metal and most cross-weld tests of friction stir weld material show similar creep lives and ductility as base metal tests. Ductility at rupture was found to exceed 30% for friction stir weld specimens, and the Norton power law exponent was determined to be between 30 and 50.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 824: Symposium CC – Scientific Basis for Nuclear Waste Management XXVIII , 2004 , CC1.13
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Werme, L, AB, Svensk Kärnbränslehantering, Technical report, TR-98-08, Stockholm, Sweden (1998).Google Scholar
2 Andersson, C-G, AB, Svensk Kärnbränslehantering, Technical report,TR–98–09, Stockholm, Sweden (1998).Google Scholar
3 Henderson, P.J., Sandström, R., Materials science and engineering A, Vol. 246, no. 1–2, pp. 143–150 (1998)Google Scholar
4 Seitisleam, F., Henderson, P.J., Lindblom, J., Swedish Institutefor Metals Research, Report IM–3327, Stockholm, Sweden (1996).Google Scholar
5 Henderson, P.J., International Seminar on Design and Manufacture of Copper Canistersfor Nuclear Waste, Sollentuna, Sweden, April (1994).Google Scholar
6 Henderson, P.J., Werme, L., Materials and Nuclear Power, EUROMAT 96, Bournemouth, United Kingdom, October (1996).Google Scholar
7 Sandström, R., Journal of Testing and Evaluation, JTEVA, Vol. 27, No. 1, pp. 31–35 (1999)Google Scholar
8 Andersson, H.C.M., Seitisleam, F., Sandström, R., AB, Svensk Kärnbränslehantering, Technical report, TR-99-39 Stockholm, Sweden (1999)Google Scholar
9 Siwecki, T., Petterson, S., Blaz, L., Swedish Institute for Metals Research, Report IM-1999-513, Stockholm, Sweden (1999).Google Scholar
10 Hamzah, S., Stålberg, U., Scandinavian Journal of Metallurgy. Vol. 30, no. 4, pp. 232–237 (2001)Google Scholar
11 Källgren, T., Sandsträm, R., 4th International Symposium on FSW, Park City, USA, April (2003)Google Scholar