Hostname: page-component-586b7cd67f-gb8f7 Total loading time: 0 Render date: 2024-11-29T07:36:31.693Z Has data issue: false hasContentIssue false
  • English
  • Français

Creep Behavior and Microstructural Stability of Lamellar γ-T1AI (Cr, Mo, Si, B) with Extremely Fine Lamellar Spacing

Published online by Cambridge University Press:  21 March 2011

Wolfram Schillinger ,
Dezhi Zhang ,
Gerhard Dehm ,
Arno Bartels  and
Helmut Clemens
Wolfram Schillinger
Affiliation:
Materials Science and Technology, TUHH, Hamburg, GERMANY
Dezhi Zhang
Affiliation:
Max-Planck-Institut für Metallforschung, Stuttgart, GERMANY
Gerhard Dehm
Affiliation:
Max-Planck-Institut für Metallforschung, Stuttgart, GERMANY
Arno Bartels
Affiliation:
Materials Science and Technology, TUHH, Hamburg, GERMANY
Helmut Clemens
Affiliation:
Institute for Materials Research, GKSS-Research Center, Geesthacht, GERMANY
Get access

Abstract

γ-T1AI (Cr, Mo, Si, B) specimens with two different fine lamellar microstructures were produced by vacuum arc melting followed by a two-stage heat treatment. The average lamellar spacing was determined to be 200 nm and 25–50 nm, respectively. Creep tests at 700°C showed a very strong primary creep for both samples. After annealing for 24 hours at 1000 °C the primary creep for both materials is significantly decreased. The steady-state creep for the specimens with the wider lamellar spacing appears to be similar to the creep behavior prior to annealing while the creep rate of the material with the previously smaller lamellar spacing is significantly higher. Optical microscopy and TEM-studies show that the microstructure of the specimens with the wider lamellar specing is nearly unchanged, whereas the previously finer material was completely recrystallized to a globular microstructure with a low creep resistance. The dissolution of the fine lamellar microstructure was also observed during creep tests at 800 °C as manifested in an acceleration of the creep rate. It is concluded that extremely fine lamellar microstructures come along with a very high dislocation density and internal stresses which causes the observed high primary creep. The microstructure has a composition far away from the thermodynamical equilibrium which leads to a dissolution of the structure even at relatively low temperatures close to the intended operating temperature of γ-T1AI structural parts. As a consequence this limits the benefit of fine lamellar microstructures on the creep behavior.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 646 , 2000 , N1.4.1
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Parthasarathy, T. A., Keller, M. and Mendiratta, M. G., Scripta Mat. 37 (7), 1025–1031 (1998).Google Scholar
[2] Maruyama, K., Yamamoto, R., Nakakuki, H., and Fujitsuna, N., Mat. Sci. And Eng. A239–240, 419–428 (1997).Google Scholar
[3] Chatterjee, A., Bolay, U., Sattler, U., and Clemens, H. in Intermetallics and Superalloys, edited by Morris, D.G., Naka, S. and Caron, P., (Proceedings of Euromat 1999 6, Wiley-VCH, 2000), pp. 233–239.Google Scholar
[4] Zhang, D., Kopold, P., Güther, V., and Clemens, H., Z. Metallkd. 91 (3), 206–210, (2000).Google Scholar
[5] Zhang, D., Arzt, E. and Clemens, H., Intermetallics 7, 1081–1087, (1999).Google Scholar