Hostname: page-component-cd9895bd7-fscjk Total loading time: 0 Render date: 2024-12-27T18:29:42.524Z Has data issue: false hasContentIssue false

Assessment of the Effect of Irradiation Temperature on the Mechanical Anisotropy of the Zr+ Ion Irradiated Zr-2.5%Nb

Published online by Cambridge University Press:  15 March 2011

Bipasha Bose
Affiliation:
Department of Mechanical and Materials Engineering, Faculty of Engineering, University of Western Ontario, London, Ontario, N6A 5B9, Canada
Robert J. Klassen
Affiliation:
Department of Mechanical and Materials Engineering, Faculty of Engineering, University of Western Ontario, London, Ontario, N6A 5B9, Canada
Get access

Abstract

We present here new information on the effect of irradiation temperature on the strength and mechanical anisotropy of Zr-2.5%Nb CANDU pressure tube material. Polished samples aligned normal to the transverse (TN), axial (AN) and radial (RN) directions of the pressure tube were irradiated at 300°C with 8.5 MeV Zr+ ions to assess the effect of concurrent thermal annealing of the irradiation damage. Constant-load micro-indentation creep tests were performed at 25°C at indentation depths from 0.1 to 2.0 μm on the ion irradiated samples.

The increase in the initial indentation stress with increasing levels of Zr+ ion irradiation at 300°C was lower than that reported earlier for similar samples exposed to Zr+ irradiation at 25°C. While the anisotropy of the indentation stress decreased significantly with Zr+ ion irradiation, the level of the decrease was reduced when the irradiation was performed at 300oC compared to 25oC. The apparent activation energy ΔG0 of the obstacles that limit the rate of dislocation glide during indentation creep did not change with indentation direction but did increase with increasing levels of Zr+ ion damage. The values of ΔG0 were, again, lower for samples that were irradiated at 300°C than for those irradiated at 25oC.

The observed differences in the magnitude of, and the anisotropy of, the initial indentation stress and also the decrease in the apparent activation energy of the indentation creep process of Zr-2.5%Nb samples irradiated with Zr+ ions at 300oC compared to those irradiated at 25oC indicate the effect that concurrent thermal annealing has on the accumulation of irradiation damage. The effect of irradiation temperature on reducing the degree of, and the strength of, irradiation induced crystallographic damage must therefore be considered when predicting the strength and thermal creep behaviour of irradiated nuclear materials.

Type
Articles
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Bose, B., Klassen, R.J., J. of Nucl. Mat. 405, 138 (2010).Google Scholar
2. Bose, B., Klassen, R.J., J. of Nucl. Mat. 399, 32 (2010).Google Scholar
3. Frost, H. J. and Ashby, M. F., Deformation-Mechanism Maps, (Pergamon Press, Oxford 1982), pp.21.Google Scholar
4. Bhakhri, V. and Klassen, R. J., J. Mater. Sci. 41, 2259 (2006).Google Scholar
5. Bhakhri, V. and Klassen, R. J., Scripta Mater. 55, 395 (2006).Google Scholar
6. Bose, B. and Klassen, R. J., Mat. Sci. and Eng. A 500, 164 (2009).Google Scholar
7. Klassen, R. J., Diak, B. J. and Saimoto, S., Mater. Sci. Eng. A 387-389, 297 (2004).Google Scholar