Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-25T17:59:11.337Z Has data issue: false hasContentIssue false
  • English
  • Français

Hydrogenated Amorphous Silicon Photoresists for Hgcdte Patterning

Published online by Cambridge University Press:  15 February 2011

R. E. Hollingsworth ,
C. DeHart ,
Li Wang ,
J. H. Dinan  and
J. N. Johnson
R. E. Hollingsworth
Affiliation:
Materials Research Group, Inc., 12441 W. 49th Ave., Wheat Ridge, CO 80033
C. DeHart
Affiliation:
Materials Research Group, Inc., 12441 W. 49th Ave., Wheat Ridge, CO 80033
Li Wang
Affiliation:
Materials Research Group, Inc., 12441 W. 49th Ave., Wheat Ridge, CO 80033
J. H. Dinan
Affiliation:
US Army CECOM Night Vision & Electronic Sensors Directorate, 10221 Burbeck Road, Fort Belvoir, VA 22060
J. N. Johnson
Affiliation:
E-OIR Measurements, Inc., 9241 Courthouse Rd., Spotsylvania, VA 22553
Get access

Abstract

A process to use a hydrogenated amorphous silicon (a-Si:H) film as a dry photoresist mask for plasma etching of HgCdTe has been demonstrated. The a-Si:H films were deposited using standard plasma enhanced chemical vapor deposition with pure silane as the source gas. X-ray photoelectron spectra show that virtually no oxide grows on the surface of an a-Si:H film after 3 hours in air, indicating that it is hydrogen passivated. Ultraviolet light frees hydrogen from the surface and enhances the oxide growth rate. A pattern of 60 micron square pixels was transferred from a contact mask to the surface of an a-Si:H film by ultraviolet enhanced oxidation in air. For the conditions used, the oxide thickness was 0.5–1.0 nm. Hydrogen plasmas were used to develop this pattern by removing the unexposed regions of the film. A hydrogen plasma etch selectivity between oxide and a-Si:H of greater than 500:1 allows patterns as thick as 700 nm to be generated with this very thin oxide. These patterns were transferred into HgCdTe by etching in an electron cyclotron resonance plasma. An etch selectivity between a-Si:H and HgCdTe of greater than 4:1 was observed after etching 2500 nm into the HgCdTe. All of the steps are compatible with processing in vacuum.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 467: Symposium A – Amorphous and Microcrystalline Silicon Technology - 1997 , 1997 , 961
Copyright
Copyright © Materials Research Society 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Arias, J.M., Pasko, J.G., Zandian, M., Kozlowski, L.J., Bajaj, J., Tennant, W.E. and DeWames, R.E., in proceedings of the IRIS Specialty Group on IR Materials, Boulder, CO, August, 1994.Google Scholar
2. Dinan, J.H., Benson, J.D., Cornfield, A.B., Martinka, M., Johnson, J.N., Bratton, J., Taylor, P., Proceedings of the 1996 EEEE/CPMT Int'l Electronics Manufacturing Technology Symposium, Austin, TX, October, 1996, p. 205.Google Scholar
3. Hollingsworth, R.E. and Bhat, P.K., Appl. Phys. Lett. 64, 616 (1994).Google Scholar
4. Graf, D., Grundner, M., Schulz, R., and Mühlhoff, L., J. Appl. Phys. 68, 5155 (1990).Google Scholar
5. Westlake, W. and Heintze, M., J. Appl. Phys. 77, 879 (1995).Google Scholar