Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-25T18:02:08.381Z Has data issue: false hasContentIssue false
  • English
  • Français

Effects of Thickness and Oxygen Content on Thermomechanical Behavior of Thin Cu Films Passivated with Ain

Published online by Cambridge University Press:  10 February 2011

J. Shu ,
S. Clyburn ,
T. Mates  and
S. P. Baker
J. Shu
Affiliation:
Department of Materials Science and Engineering, Cornell University, Ithaca, NY 14853–1501.
S. Clyburn
Affiliation:
Department of Materials Science and Engineering, Cornell University, Ithaca, NY 14853–1501.
T. Mates
Affiliation:
Materials Department, University of California, Santa Barbara, CA 93106–5050.
S. P. Baker
Affiliation:
Department of Materials Science and Engineering, Cornell University, Ithaca, NY 14853–1501.
Get access

Abstract

The thermomechanical behavior of a Cu thin film can be dramatically influenced (“oxygen effect”) by exposing the film to a small amount of air or oxygen prior to passivation. Film exposure is accomplished by breaking vacuum at some point prior to passivation. When the top surface is exposed immediately before passivation, the oxygen effect is produced when the passivation material is Si3N4, but no effect is seen with AIN passivations. However, the effect is seen in AIN passivated films when the Cu film surface is exposed to air or O2 and additional Cu is deposited before passivation. This suggests that conditions at the film/passivation interface are an important factor in this anomalous plasticity effect. We have investigated the effects of film thickness and oxygen concentration on these behaviors by preparing films with different thicknesses and oxygen contents for thermomechanical analysis. The thermomechanical behavior is correlated with secondary ion mass spectrometry (SIMS) data that shows oxygen concentration vs. film depth. The presence of the “oxygen effect” in thermomechanical behavior is found to be correlated with an increased oxygen concentration near the film/passivation and film/barrier interfaces.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 563: Symposium M – Materials Reliability in Microelectronics IX , 1999 , 207
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Baker, S.P., Keller, R.-M. and Arzt, E., in Thin Films: Stresses and Mechanical Properties VII, (Edited by Cammarata, R. C., Busso, E. P., Nastasi, M. and Oliver, W. C.). Proc. Materials Research Society, Warrendale PA, Vol. 505, (1998) p. 605 Google Scholar
2. Keller, R.-M., Baker, S.P. and Arzt, E., Journal of Materials Research 66 1307 (1998).Google Scholar
3. Vinci, R.P., Zielinski, E.M. and Bravman, J.C., Thin Solid Films 262, 142 (1995).Google Scholar
4. Vinci, R.P., personal communication (1997).Google Scholar
5. Keller, R.-M., Sigle, W., Baker, S.P., Kraft, O. and Arzt, E., in Thin Films: Stresses and Mechanical Properties VI, (Edited by Gerberich, W. W., Gao, H., Sundgren, J.-E. and Baker, S. P.). Proc. Materials Research Society, Pittsburg, PA, Vol. 436, (1996) p. 221.Google Scholar
6. Keller, R.-M., “Thermomechanical Behavior and Microstructure of Thin Polycrystalline Copper Films” (in German) Ph. D. Dissertation, Universitdit Stuttgart, (1996).Google Scholar