Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-26T12:17:49.219Z Has data issue: false hasContentIssue false
  • English
  • Français

Novel Superconducting Joints for Persistent Mode Magnet Applications

Published online by Cambridge University Press:  10 June 2016

Tayebeh Mousavi ,
William Darby ,
Canan Aksoy ,
Timothy Davies ,
Greg Brittles ,
Chris Grovenor  and
Susannah Speller
Tayebeh Mousavi
Affiliation:
Materials Department, Oxford University, OX1 3PH, Oxford, UK.
William Darby
Affiliation:
Materials Department, Oxford University, OX1 3PH, Oxford, UK.
Canan Aksoy
Affiliation:
Electronic and Communication Department, Faculty of Technology, Karadeniz Technical University, 61830, Trabzon, Turkey.
Timothy Davies
Affiliation:
Materials Department, Oxford University, OX1 3PH, Oxford, UK.
Greg Brittles
Affiliation:
Materials Department, Oxford University, OX1 3PH, Oxford, UK.
Chris Grovenor
Affiliation:
Materials Department, Oxford University, OX1 3PH, Oxford, UK.
Susannah Speller*
Affiliation:
Materials Department, Oxford University, OX1 3PH, Oxford, UK.
*
*(Email: [email protected])
Get access

Abstract

Persistent current joints are a critical component of commercial superconducting magnets.The standard jointing method widely used in the magnet industry for technological low temperature superconducting wires such as NbTi and Nb3Sn wires uses a superconducting solder (e.g. PbBi). In these joints the physical and superconducting properties of the solder materials inevitably play an important role in the overall performance of the joint. Key requirements for superconducting solders include low melting point to prevent degradation of the superconducting filaments during joining, good wettability of the superconducting filaments, suitable liquid phase viscosity, and finally adequate superconducting properties to enable sufficient supercurrent to pass through the joint under typical operating conditions (typically at 4.2K in a field of 1 T for an MRI magnet). PbBi solder satisfies all these criteria, but restrictions on the use of lead in the magnet industry are expected in the relatively near future, so new lead-free jointing techniques need to be developed.

One approach is the development of superconducting lead-free solder materials. In our work, we have focussed on the In-Sn system and ternary systems involving In and Sn as two of the elements. Thermodynamic modelling has been used to produce ternary phase diagrams of potential alloy systems, and various formulations have been fabricated in order to explore how microstructure and phase chemistry influence the superconducting properties of the solders. Alternative approaches to fabricating lead-free joints, including spot welding and cold-pressing, have also been investigated. These methods have the potential advantage of achieving direct NbTi-NbTi joints with no intermediate, lower performance superconducting material. The spot welding method produced joints with the best superconducting performance, signifiantly better than the currently used PbBi solder, but the lack of reproducibility in this technique may be a problem from an industrial point of view.

Keywords

joiningmagnetic propertiessuperconducting
Type
Articles
Information
MRS Advances , Volume 1 , Issue 51: Electronics and Photonics , 2016 , pp. 3483 - 3488
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Thornton, R.F., U.S. Patent No. 4584547, (1986).Google Scholar
Fukuzaki, T., Maeda, H., Matsumoto, S., Nimori, S., Yokoyama, S. and Kiyoshi, T., IEEE Trans. Appl. Supercond. 16, 1547–9, (2006).Google Scholar
Swenson, C. A. and Markiewicz, W.D., IEEE Trans. Appl. Supercond. 9, 185–8, (1999).CrossRefGoogle Scholar
Levy, S. A., J. Appl. Phys. 37, 3659, (1966).Google Scholar
Evetts, J. E. and Wade, J.M., J. Phys. Chem. Solids. 31, 973–82, (1970).Google Scholar
Brittles, G., Mousavi, T., Aksoy, C., Grovenor, C. and Speller, S., Supercond. Sci. Technol. 28, 093001, (2015).Google Scholar
Mousavi, T., Aksoy, C., Grovenor, C., Speller, S., Supercond. Sci. Technol. 29, 015012, (2016).Google Scholar
Mousavi, T., Aksoy, C., Grovenor, C., Speller, S., Trans. Appl. Supercond., doi. 10.1109/TASC.2016.2514843, (2016).Google Scholar
Aksoy, C., Mousavi, T., Brittles, G., Grovenor, C., Speller, S., Trans. Appl. Supercond., doi. 10.1109/TASC.2016.2539423, (2016).Google Scholar
Carter, Giles F. and Paul, Donald E., Materials Science and Engineering, ASM International, (1991).Google Scholar