Hostname: page-component-78c5997874-s2hrs Total loading time: 0 Render date: 2024-11-05T16:59:51.153Z Has data issue: false hasContentIssue false

Microstructural Characterization of Aluminum-Carbon Nanotube Nanocomposites Produced Using Different Dispersion Methods

Published online by Cambridge University Press:  08 March 2016

Sónia Simões*
Affiliation:
Department of Metallurgical and Materials Engineering, CEMUC, University of Porto, R. Dr. Roberto Frias, 4200-465 Porto, Portugal
Filomena Viana
Affiliation:
Department of Metallurgical and Materials Engineering, CEMUC, University of Porto, R. Dr. Roberto Frias, 4200-465 Porto, Portugal
Marcos A. L. Reis
Affiliation:
Faculdade de Ciências Exatas e Tecnologia, Universidade Federal do Pará, Abaetetuba, PA 68440-000, Brazil
Manuel F. Vieira
Affiliation:
Department of Metallurgical and Materials Engineering, CEMUC, University of Porto, R. Dr. Roberto Frias, 4200-465 Porto, Portugal
*
*Corresponding author. [email protected]
Get access

Abstract

This research focuses on characterization of the impact of dispersion methods on aluminum-carbon nanotubes (Al-CNTs) nanocomposite structure. Nanocomposites were produced by a conventional powder metallurgy process after the dispersion of the CNTs on the Al powders, using two approaches: (1) the dispersion of CNTs and mixture with Al powders were performed in a single step by ultrasonication; and (2) the CNTs were previously untangled by ultrasonication and then mixed with Al powders by ball milling. Microstructural characterization of Al-CNT nanocomposites was performed by optical microscopy, scanning and transmission electron microscopy, electron backscatter diffraction, and high-resolution transmission electron microscopy (HRTEM). Microstructural characterization revealed that the use of ball milling for mixing CNTs with Al powders promoted the formation of CNT clusters of reduced size, more uniformly dispersed in the matrix, and a nanocomposite of smaller grain size. However, the results of HRTEM and Raman spectroscopy show that ball milling causes higher damage to the CNT structure. The strengthening effect of the CNT is attested by the increase in hardness and tensile strength of the nanocomposites.

Type
Papers from the 4th Joint Congress of the Portuguese and Spanish Microscopy Societies
Copyright
Copyright © Microscopy Society of America 2016

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Bakshi, S.R. & Agarwal, A. (2011). An analysis of the factors affecting strengthening in carbon nanotube reinforced aluminum composites. Carbon 49, 533544.Google Scholar
Bakshi, S.R., Keshri, A.K., Singh, V., Seal, S. & Agarwal, A. (2009). Interface in carbon nanotube reinforced aluminum silicon composites: Thermodynamic analysis and experimental verification. J Alloys Compd 481, 207213.Google Scholar
Bakshi, S.R., Lahiri, D. & Agarwal, A. (2010). Carbon nanotube reinforced metal matrix composites—a review. Int Mater Rev 55, 4164.Google Scholar
Baughman, R.H., Zakhidov, A.A. & de Heer, W.A. (2002). Carbon nanotubes—the route toward applications. Science 297, 787792.Google Scholar
Bradbury, C.R., Gomon, J.K., Kollo, L., Kwon, H. & Leparoux, M. (2014). Hardness of multi wall carbon nanotubes reinforced aluminium matrix composites. J Alloys Compd 585, 362367.Google Scholar
Choi, H.J., Min, B.H., Shin, J.H. & Bae, D.H. (2011 a). Strengthening in nanostructured 2024 aluminum alloy and its composites containing carbon nanotubes. Compos Part A Appl Sci Manuf 42, 14381444.Google Scholar
Choi, H.J., Shin, J.H. & Bae, D.H. (2011 b). Grain size effect on the strengthening behavior of aluminum-based composites containing multi-walled carbon nanotubes. Compos Sci Technol 71, 16991705.Google Scholar
Dong, S., Zhou, J., Liu, H., Wua, Y. & Qi, D. (2015). The strengthening effect of carbon nanotube in metal matrix composites considering interphase. Mech Mater 91, 111.Google Scholar
Esawi, A.M.K. & El Borady, M.A. (2008). Carbon nanotube-reinforced aluminium strips. Compos Sci Technol 68, 486492.Google Scholar
George, R., Kashyap, K.T., Rahul, R. & Yamdagni, S. (2005). Strengthening in carbon nanotube/aluminium (CNT/Al) composites. Scr Mater 53, 11591163.Google Scholar
Jiang, L., Fan, G., Li, Z., Kai, X., Zhang, D., Chen, Z., Humphries, S., Hness, G. & Yeung, W.Y. (2011). An approach to the uniform dispersion of a high volume fraction of carbon nanotubes in aluminum powder. Carbon 49, 19651971.Google Scholar
Kainer, K.U. (2006). Metal Matrix Nanocomposites: Custom-Made Materials for Automative and Aerospace Engineering. Weinheim: WILEY-VCH Verlag GmbH & Co. KGaA.Google Scholar
Kelly, A. & Tyson, W. R. (1965). Tensile properties of fiber-reinforced metal: Copper/tungsten and copper/molybdenum. J Mech Phys Solids 13, 329350.Google Scholar
Keszler, A.M., Nemes, L., Ahmad, S. & Kawasaki, A. (2004). Characterization of carbon nanotube materials by Raman spectroscopy—A case study of multiwalled and singlewalled samples. J Optoelectron Adv Mater 6, 12691274.Google Scholar
Kuzumaki, T., Miyazawa, K., Ichinose, H. & Ito, K. (1998). Processing of carbon nanotube reinforced aluminum composite. J Mater Res 13, 24452449.Google Scholar
Kwon, H. & Leparoux, M. (2012). Hot extruded carbon nanotube reinforced aluminum matrix composite materials. Nanotechnology 23, 415701.Google Scholar
Li, C.-D., Wang, X.-J., Liu, W.-Q., Wu, K., Shi, H.-L., Ding, C. & Zheng, M.-Y. (2016). Microstructure and mechanical properties of magnesium matrix composite reinforced with carbon nanotubes by ultrasonic vibration. Rare Met, doi 10.1007/s12598-015-0561-y.Google Scholar
Liu, Z.Y., Xu, S.J., Xiao, B.L., Xue, P., Wang, W.G. & Ma, Z.Y. (2012). Effect of ball-milling time on mechanical properties of carbon nanotubes reinforced aluminum matrix composites. Compos Part A Appl Sci Manuf 43, 21612168.Google Scholar
Noguchi, T., Magario, A., Fukazawa, S., Shimizu, S., Beppu, J. & Seki, M. (2004). Carbon nanotube/aluminium composites with uniform dispersion. Mater Trans 45, 602604.Google Scholar
Peng, T. & Chang, I. (2015). Uniformly dispersion of carbon nanotube in aluminum powders by wet shake-mixing approach. Powder Technol 284, 3239.Google Scholar
Perez-Bustamante, R., Perez-Bustamante, F., Estrada-Guel, I., Santillan-Rodriguez, C.R., Matutes-Aquino, J.A., Herrera-Ramirez, J.M., Miki-Yoshida, M. & Martinez-Sanchez, R. (2011). Characterization of Al-2024—CNTs composites produced by mechanical alloying. Powder Technol 212, 390396.Google Scholar
Simões, S., Viana, F., Reis, M.A.L. & Vieira, M.F. (2014). Improved dispersion of carbon nanotubes in aluminum nanocomposites. Compos Struct 108, 9921000.Google Scholar
Simões, S., Viana, F., Reis, M.A.L. & Vieira, M.F. (2015 a). Influence of dispersion/mixture time on mechanical properties of Al-CNTs nanocomposites. Compos Struct 126, 114122.Google Scholar
Simões, S., Viana, F., Reis, M.A.L. & Vieira, M.F. (2015 b). TEM and HRTEM characterization of nanocomposites reinforced with carbon nanotubes. Microsc Microanal 21(Suppl 6), 8687.Google Scholar
Tjong, S.C. (2009). Carbon Nanotube Reinforced Nanocomposites. Weinheim: Wiley-VCH Verlag GmbH & Co. KGaA.Google Scholar