Hostname: page-component-78c5997874-94fs2 Total loading time: 0 Render date: 2024-11-17T19:06:01.319Z Has data issue: false hasContentIssue false
  • English
  • Français

Influence of Crystallographic Texture on Young's Modulus of Various Alloy 82H Welds

Published online by Cambridge University Press:  08 April 2011

Steven R. Claves  and
William J. Mills
Steven R. Claves*
Affiliation:
Materials Technology, Bechtel Marine Propulsion Corporation, West Mifflin, PA 15221, USA
William J. Mills
Affiliation:
Materials Technology, Bechtel Marine Propulsion Corporation, West Mifflin, PA 15221, USA
*
Corresponding author. E-mail: [email protected]
Get access

Abstract

Electron backscatter diffraction (EBSD) was employed to analyze the microstructure and texture of four different Alloy 82H gas tungsten arc welds that previously underwent static and dynamic modulus testing. The Young's moduli were shown to differ among the various welds, but also within each weld, dependent upon the direction measured. These differences were attributed to anisotropy of the crystallographic textures, which were described using inverse pole figures with respect to each of the weld's three orthogonal axes. The Young's modulus demonstrated a strong correlation with the texture, consistent with single crystal experiments. Sample directions containing a large population of {100} orientations had the lowest Young's modulus, while those with {111} grains possessed the highest. Microstructures with {110} textures were closer to the average modulus value of 207 GPa (30.0 Msi). X-ray diffraction texture measurements on four samples were used to verify the EBSD results.

Keywords

EBSDYoung's modulusmicrotextureAlloy 82HweldsGTAanisotropy
Type
Electron Backscatter Diffraction Special Section
Information
Microscopy and Microanalysis , Volume 17 , Issue 3 , June 2011 , pp. 341 - 349
Copyright
Copyright © Microscopy Society of America 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

ASME (2004). Boiler and Pressure Vessel Code, Section II, Part C, Specifications for Welding Rods, Electrodes, and Filler Metals: SFA-5.14 Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods. New York: The American Society of Mechanical Engineers.Google Scholar
ASTM (2007). Annual Book of ASTM Standards, Section 3, Volume 03.01, E1876-01, Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Impulse Excitation of Vibration. West Conshohocken, PA: ASTM International.Google Scholar
Brandes, E.A. (1983). Smithells Metals Reference Book 6th Edition, pp. 15-1–15-8. London, UK: Butterworth & Co Ltd.Google Scholar
Callister, W.D. Jr. (2000). Materials Science and Engineering—An Introduction, pp. 118–120. New York: John Wiley & Sons, Inc.Google Scholar
Hicken, G.K. (1993). Gas-tungsten arc welding. In ASM Handbook, Volume 6: Welding, Brazing, and Soldering, Olsen, D.L., Siewert, T.A., Liu, S. & Edwards, G.R. (Eds.), pp. 190–194. Materials Park, OH: ASM International.CrossRefGoogle Scholar
Schwartz, A.J., Kumar, M., Adams, B.L. & Field, D.P. (2009). Electron Backscatter Diffraction in Materials Science 2nd Edition. New York: Springer.CrossRefGoogle Scholar
Wenk, H.-R. (1998). Pole figure measurements with diffraction techniques. In Texture and Anisotropy Preferred Orientations in Polycrystals and Their Effect on Materials Properties, Kocks, U.F., Tomé, C.N. & Wenk, H.-R. (Eds.), pp. 127–149. Cambridge, UK: Cambridge University Press.Google Scholar