Hostname: page-component-78c5997874-lj6df Total loading time: 0 Render date: 2024-11-06T10:59:26.985Z Has data issue: false hasContentIssue false

Studies on mechanical behavior and microstructural analysis of tailor welded blanks of Ti–6Al–4V titanium alloy sheet

Published online by Cambridge University Press:  21 April 2016

A. Karpagaraj
Affiliation:
Department of Mechanical Engineering, National Institute of Technology, Tiruchirappalli-620 015, Tamil Nadu, India
N. Siva Shanmugam*
Affiliation:
Department of Mechanical Engineering, National Institute of Technology, Tiruchirappalli-620 015, Tamil Nadu, India
K. Sankaranarayanasamy
Affiliation:
Department of Mechanical Engineering, National Institute of Technology, Tiruchirappalli-620 015, Tamil Nadu, India
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

In the present study, Ti–6Al–4V alloy sheets having a thickness of 1.6 mm and 2 mm are chosen for carrying out weldability studies using gas tungsten arc welding (GTAW) process. The quality of the weld was examined through metallographic (macro- and micrographs) analyses. The welded specimens were subjected to mechanical tests to examine the behavior of tailor welded blanks (TWBs). Grain coarsening at fusion zone (FZ) and heat affected zone was confirmed through optical microscope. Transmission electron microscopy images showed the presence of thin α-phases surrounded by β-grains at FZ. The maximum hardness distribution of 383 HV is obtained at FZ. Tensile test results revealed an increase of 3.58% strength as compared to the thin base metal. At fracture surface, the presence of various sized dimples was identified through SEM. Erichsen cupping test showed that formability performance of the TWB was affected by a negligible percentage.

Type
Articles
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Jürgen Eckert

References

REFERENCES

Morishita, Y., Kado, T., Abe, S., Sakamoto, Y., and Yoshida, F.: Role of counterpunch for square-cup drawing of tailored blank composed of thick/thin sheets. J. Mater. Process. Technol. 212, 2102 (2012).CrossRefGoogle Scholar
Mohrbacher, H., Spottl, M., and Paegle, J.: Innovative manufacturing technology enabling light weighting with steel in commercial vehicles. Adv. Manuf. 3, 3 (2015).CrossRefGoogle Scholar
Qi, Y.: The new technology in the automotive industry by using tailor welded blanks. (Undated). Available at: http://www.baosteel.com/english_n/e07technical_n/21be.pdf (accessed 28 November 2015).Google Scholar
Merklein, M., Johannes, M., Lechner, M., and Kuppert, A.: A review on tailored blank production, applications and evaluation. J. Mater. Process. Technol. 214, 151 (2014).CrossRefGoogle Scholar
Panda, S.K., Kumar, D.R., Kumar, H., and Nath, A.K.: Characterization of tensile properties of tailor welded IF steel sheets and their formability in stretch forming. J. Mater. Process. Technol. 183, 321 (2007).Google Scholar
Korouyeh, R.S., Naeini, H.M., Torkamany, M.J., and Liaghat, G.: Experimental and theoretical investigation of thickness ratio effect on the formability of tailor welded blank. Opt. Laser Technol. 51, 24 (2013).CrossRefGoogle Scholar
Babu, K.V., Narayanan, R.G., and Kumar, G.S.: An expert system based on artificial neural network for predicting the tensile behaviour of tailor welded blanks. Expert Syst. Appl. 36, 10683 (2009).CrossRefGoogle Scholar
Piwnik, J., Hadrys, D., and Skorulski, G.: Plastic properties of weld after micro-jet cooling. Arch. Mater. Sci. Eng. 59, 20 (2013).Google Scholar
Tajally, M. and Emadoddin, E.: Mechanical and anisotropic behaviours of 7075 aluminum alloy sheets. Mater. Des. 32, 1594 (2011).CrossRefGoogle Scholar
Winowiecka, J., Wieckowski, W., and Zawadzki, M.: Evaluation of draw ability of tailor-welded blanks made of titanium alloys grade 2||grade 5. Comput. Mater. Sci. 77, 108 (2013).CrossRefGoogle Scholar
Anand, D., Chen, D.L., Bhole, S.D., Andreychuck, P., and Boudreau, G.: Fatigue behaviour of tailor (laser)-welded blanks for automotive applications. Mater. Sci. Eng., A 420, 199 (2006).Google Scholar
Davies, R.W., Oliver, H.E., Smith, M.T., and Grant, G.J.: Characterizing Al tailor-welded blanks for automotive applications. JOM 51, 46 (1999).CrossRefGoogle Scholar
Suresh, V.S., Regalla, S.P., Gupta, A.K., and Padmanabham, G.: Weld Line Shift in the case of tailor welded blanks subjected to differential strengths with respect to TIG and laser welding. Mater. Today. Proc. 2, 3501 (2015).CrossRefGoogle Scholar
Kleiner, M., Geiger, M., and Klaus, A.: Manufacturing of lightweight components by metal forming. CIRP Ann. 52, 521 (2003).CrossRefGoogle Scholar
Patel, B.C., Shah, J., and Shah, H.: Review on formability of tailor-welded blanks. ISSN (Print): 2319 (2012).Google Scholar
Adamus, J. and Lacki, P.: Analysis of forming titanium welded blanks. Comput. Mater. Sci. 94, 66 (2014).Google Scholar
Xu, W., Westerbaan, D., Nayak, S.S., Chen, D.L., Goodwin, F., and Zhou, Y.: Tensile and fatigue properties of fiber laser welded high strength low alloy and DP980 dual-phase steel joints. Mater. Des. 43, 373 (2013).CrossRefGoogle Scholar
Pallett, R.J. and Lark, R.J.: The use of tailored blanks in the manufacture of construction components. J. Mater. Process. Technol. 117, 249 (2001).Google Scholar
Giridharan, P.K. and Murugan, N.: Optimization of pulsed GTA welding process parameters for the welding of AISI 304L stainless steel sheets. Int. J. Adv. Manuf. Tech. 40, 478 (2009).Google Scholar
Karpagaraj, A., Siva Shanmugam, N., and Sankaranarayanasamy, K.: Some studies on mechanical properties and microstructural characterization of automated TIG welding of thin commercially pure titanium sheets. Mater. Sci. Eng., A 640, 180 (2015).Google Scholar
Balasubramanian, T.S., Balasubramanian, V., and Muthumanikkam, M.A.: Fatigue performance of gas tungsten arc, electron beam and laser beam welded Ti–6Al–4V alloy joints. J. Mater. Eng. Perform. 20, 1620 (2011).Google Scholar
Sundaresan, S., Ram, G.J., and Reddy, G.M.: Microstructural refinement of weld fusion zones in α–β titanium alloys using pulsed current welding. Mater. Sci. Eng., A 262, 88 (1999).Google Scholar
Liu, H.J., Zhou, L., and Liu, Q.W.: Microstructural characteristics and mechanical properties of friction stir welded joints of Ti–6Al–4V titanium alloy. Mater. Des. 31, 1650 (2010).Google Scholar
Squillace, A., Prisco, U., Ciliberto, S., and Astarita, A.: Effect of welding parameters on morphology and mechanical properties of Ti–6Al–4V laser beam welded butt joints. J. Mater. Process. Technol. 212, 427 (2012).Google Scholar
Caiazzo, F., Curcio, F., Daurelio, G., and Memola Capece Minutolo, F.: Ti6Al4V sheets lap and butt joints carried out by CO2 laser: Mechanical and morphological characterization. J. Mater. Process. Technol. 149, 546 (2004).Google Scholar
Balasubramanian, T.S., Balakrishnan, M., Balasubramanian, V., and Muthu manickam, M.A.: Influence of welding processes on microstructure, tensile and impact properties of Ti–6Al–4V alloy joints. Trans. Nonferrous Met. Soc. China 21, 1253 (2011).Google Scholar
Akman, E., Demir, A., Canel, T., and Sinmazçelik, T.: Laser welding of Ti6Al4V titanium alloys. J. Mater. Process. Technol. 209, 3705 (2009).Google Scholar
Wanjara, P., Brochu, M., and Jahazi, M.: Thin gauge titanium manufacturing using multiple-pass-electron beam welding. Mater. Manuf. Processes 21, 439 (2006).Google Scholar
Meinders, T., Van den Berg, A., and Huetink, J.: Deep drawing simulations of tailored blanks and experimental verification. J. Mater. Process. Technol. 103, 65 (2000).Google Scholar
Wu, Q., Gong, J., Chen, G., and Xu, L.: Research on laser welding of vehicle body. Opt. Laser Technol. 40, 420 (2008).Google Scholar
Keeler, S.P.: Circular grid system a valuable aid for evaluating sheet metal formability. SAE Technical Paper, 680092 (1968).CrossRefGoogle Scholar
Kamp, A., Celotto, S., and Hanlon, D.N.: Effects of tempering on the mechanical properties of high strength dual-phase steels. Mater. Sci. Eng., A 538, 35 (2012).Google Scholar
Lai, C.P., Chan, L.C., and Chow, C.L.: Effects of tooling temperatures on formability of titanium TWBs at elevated temperatures. J. Mater. Process. Technol. 191, 157 (2007).CrossRefGoogle Scholar
Chan, L.C., Chan, S.M., Cheng, C.H., and Lee, T.C.: Formability and weld zone analysis of tailor-welded blanks for various thickness ratios. J. Eng. Mater. Technol. 127, 179 (2005).Google Scholar