Hostname: page-component-cd9895bd7-dk4vv Total loading time: 0 Render date: 2024-12-23T12:31:32.976Z Has data issue: false hasContentIssue false
  • English
  • Français

A new method to study the effect of M–A constituent on impact toughness of IC HAZ in Q690 steel

Published online by Cambridge University Press:  11 June 2015

Zhenshun Li ,
Lei Tian ,
Bin Jia  and
Shengli Li
Zhenshun Li*
Affiliation:
School of Materials Science and Engineering, Shandong University, Jinan 250061, People's Republic of China; and Linyi Branch, Shandong Special Equipment Inspection Institute, Linyi 276007, People's Republic of China
Lei Tian
Affiliation:
School of Materials Science and Engineering, Shandong University, Jinan 250061, People's Republic of China
Bin Jia
Affiliation:
School of Materials Science and Engineering, Shandong University, Jinan 250061, People's Republic of China
Shengli Li*
Affiliation:
School of Materials Science and Engineering, Shandong University, Jinan 250061, People's Republic of China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

This paper details an investigation into the effect of martensite–austenite (M–A) constituent on impact toughness of intercritical heat-affected zone (IC HAZ) in Q690 steel, a low carbon bainitic steel. Large samples with uniform microstructure similar to that of the actual IC HAZ were achieved through combinations of heat treatments. The samples were heated to temperature between 750 and 830 °C for 30 min and then quenched in water. After these heat treatments, hard martensite islands distribute along the boundaries of soft matrix, and the size of martensite islands increases with heating temperature. The microstructure is quite similar to that of the IC HAZ. Using these large samples, the impact toughness could be measured conveniently. It was found that the embrittlement of the IC HAZ depends on the deformability and size of the M–A constituent. When the size of the M–A constituent whose deformability is low exceeds a critical value (2.0 μm), the embrittlement of the IC HAZ occurs.

Keywords

M–A constituentheat treatmentintercritical heat-affected zoneimpact toughness
Type
Articles
Information
Journal of Materials Research , Volume 30 , Issue 12 , 28 June 2015 , pp. 1973 - 1978
Copyright
Copyright © Materials Research Society 2015 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Qiu, H., Mori, H., Enoki, M., and Kishi, T.: Fracture mechanism and toughness of the welding heat-affected zone in structural steel under static and dynamic loading. Metall. Mater. Trans. A 31, 2785 (2000).CrossRefGoogle Scholar
Lee, S., Kim, B.C., and Kwon, D.: Fracture toughness analysis of heat-affected zones in high-strength low-alloy steel welds. Metall. Trans. A 24, 1133 (1993).CrossRefGoogle Scholar
Gliha, V., Vuherer, T., Ule, B., and Vojvodic-Tuma, J.: Fracture resistance of simulated heat affected zone areas in HSLA structural steel. Sci. Technol. Weld. Joining 9, 399 (2004).CrossRefGoogle Scholar
Matsuda, F., Ikeuchi, K., Fukada, Y., Horii, Y., Okada, H., Shiwaku, T., Shiga, C., and Suzuki, S.: Review of mechanical and metallurgical investigations of MA constituent in welded joint in Japan. Trans. JWRI 24(1), 1–11 (1995).Google Scholar
Lambert, A., Drillet, J., Gourgues, A.F., Sturel, T., and Pineau, A.: Microstructure of martensite-austenite constituents in heat affected zones of high strength low alloy steel welds in relation to toughness properties. Sci. Technol. Weld. Joining 5, 168 (2000).CrossRefGoogle Scholar
Kweon, K.S., Kim, J.H., Hong, J.H., and Lee, C.H.: Microstructure and toughness of intercritically reheated heat affected zone in reactor pressure vessel steel weld. Sci. Technol. Weld. Joining 5, 161 (2000).CrossRefGoogle Scholar
Kim, S., Im, Y-R., Lee, S., Lee, H-C., Jun Oh, Y., and Hong, J.H.: Effects of alloying elements on mechanical and fracture properties of base metals and simulated heat-affected zones of SA 508 steels. Metall. Mater. Trans. A 32A, 903 (2001).CrossRefGoogle Scholar
Mohseni, P., Solberg, J.K., Karlsen, M., Akselsen, O.M., and Østby, E.: Investigation of mechanism of cleavage fracture initiation in intercritically coarse grained heat affected zone of HSLA steel. Mater. Sci. Technol. 28, 1261 (2012).CrossRefGoogle Scholar
Liu, C., Zhao, Z-B., and Northwood, D.O.: Mechanical properties of heat affected zone in bainitic high strength low alloy steel. Mater. Sci. Technol. 18, 1325 (2002).CrossRefGoogle Scholar
Kaplan, D. and Lambert-Perlade, A.: Influence of martensite-austenite constituents on heat affected zone toughness of C-Mn steel welds. Rev. Metall. 98, 889 (2001).CrossRefGoogle Scholar
Moeinifar, S., Kokabi, A.H., and Hosseini, H.R.M.: Effect of tandem submerged arc welding process and parameters of Gleeble simulator thermal cycles on properties of the intercritically reheated heat affected zone. Mater. Des. 32, 869 (2011).CrossRefGoogle Scholar
Li, Y., Crowther, D.N., Green, M.J.W., Mitchell, P.S., and Baker, T.N.: The effect of vanadium and niobium on the properties and microstructure of the intercritically reheated coarse grained heat affected zone in low carbon microalloyed steels. ISIJ Int. 41, 46 (2001).CrossRefGoogle Scholar
Davis, C.L. and King, J.E.: Cleavage initiation in the intercritically reheated coarse-grained heat-affected zone: Part I. Fractographic evidence. Metall. Mater. Trans. A 25, 563 (1994).CrossRefGoogle Scholar
Ohya, K., Kim, J., Yokoyama, K., and Nagumo, M.: Microstructures relevant to brittle fracture initiation at the heat-affected zone of weldment of a low carbon steel. Metall. Mater. Trans. A 27, 2574 (1996).CrossRefGoogle Scholar
Komazaki, S-i., Sugimoto, T., Hasegawa, Y., and Kohno, Y.: Damage evaluation of a welded joint in a long-term service-exposed boiler by using a small punch creep test. ISIJ Int. 47, 1228 (2007).CrossRefGoogle Scholar
Shi, Y. and Han, Z.: Effect of weld thermal cycle on microstructure and fracture toughness of simulated heat-affected zone for a 800 MPa grade high strength low alloy steel. J. Mater. Process. Technol. 207, 30 (2008).CrossRefGoogle Scholar
Biss, V. and Cryderman, R.L.: Martensite and retained austenite in hot-rolled, low-carbon bainitic steels. Metall. Mater. Trans. B 2, 2267 (1971).CrossRefGoogle Scholar
Ale, R.M., Rebello, J.M.A., and Charlier, J.: A metallographic technique for detecting martensite-austenite constituents in the weld heat-affected zone of a micro-alloyed steel. Mater. Charact. 37, 89 (1996).CrossRefGoogle Scholar
Bonnevie, E., Ferriere, G., Ikhlef, A., Kaplan, D., and Orain, J.M.: Morphological aspects of martensite–austenite constituents in intercritical and coarse grain heat affected zones of structural steels. Mater. Sci. Eng., A 385, 352 (2004).CrossRefGoogle Scholar
Lan, L., Qiu, C., Zhao, D., Gao, X., and Du, L.: Microstructural characteristics and toughness of the simulated coarse grained heat affected zone of high strength low carbon bainitic steel. Mater. Sci. Eng., A 529, 192 (2011).CrossRefGoogle Scholar
Hrivnak, I., Matsuda, F., Li, Z., Ikeuchi, K., and Okada, H.: Investigation of metallography and behavior of MA Constituent in Weld HAZ of HSLA steels. Trans. JWRI 21, 101 (1992).Google Scholar
Li, Y. and Baker, T.N.: Effect of morphology of martensite–austenite phase on fracture of weld heat affected zone in vanadium and niobium microalloyed steels. Mater. Sci. Technol. 26, 1029 (2010).CrossRefGoogle Scholar
Moeinifar, S., Kokabi, A.H., and Hosseini, H.R.M.: Role of tandem submerged arc welding thermal cycles on properties of the heat affected zone in X80 microalloyed pipe line steel. J. Mater. Process. Technol. 211, 368 (2011).CrossRefGoogle Scholar