We have experimentally investigated the collisionless shock acceleration of ions via the interaction of a relativistic intensity (3 × 1019 W/cm2), 1.053 µm wavelength laser pulse with an underdense plasma. This plasma is formed through the use of a novel cluster jet design that allows for control of the plasma peak density and front scale length without the use of additional plasma-forming laser pulses. When the front density scale length of the target plasma is less than 60 µm, the laser pulse (1 J, 400 fs) is capable of launching an electrostatic shock wave that accelerates a proton beam. This beam is shown to have a narrow divergence angle of 0.8°, a peak flux of 14 × 106 protons/sr with an ion energy exceeding 440 keV. Particle-in-cell simulations indicate this narrow ion beam is produced by converging shocks generated via filamentation of the laser pulse in high-density (near critical) plasma.

The gas dynamics of shock-induced gas filtration through densely packed granular columns with vastly varying shock intensity and the structural parameters are numerically investigated using a coupled Eulerian–Lagrangian approach. The results shed fundamental light on the thermal effects of the shock-induced gas filtration manifested by a distinctive self-heating hot gas layer traversing the medium. The characteristics of the thermal effects in terms of the thermal intensity and uniformity are found to vary with the shock Mach number, Ms, and the filtration coefficient of the granular media, Π. As the incident shock transitions from weak to strong, and (or) the filtration coefficient increases from O(10−5) to O(104), the heating mechanisms transition between three distinct heating modes. A phase diagram of heating modes is established on the parameter space (Ms, Π), which enables us to predict the characteristics of the thermal effect in different shock-induced gas filtrations. The thermal effects markedly accelerate the pressure diffusion due to the additional heat influx when the time scale of the former is smaller than or comparable to the latter. Based on the contour map displaying the coupling degree of the thermal effects and the pressure diffusion, we identify a decoupling criterion whereby the isothermal assumption holds if only the pressure diffusion is concerned. The thermal effects may well bring about considerable thermal shocks which pose a great threat to the integrity of the solid skeleton and further reduce the overall shock resistance performance of the porous media.

In this paper, curved detonation equations with gradients for the pre-wave and post-wave are constructed followed by analysis, verification and applications. The study focuses on shock induced chemical reaction such as detonation, with the energy effect for the main attention. Equations consider both planar and transverse curvature to accommodate both planar and axisymmetric flow problems. Influence coefficients are derived and used to analyse the effect of energy and curvature on the post-wave gradient. Good agreement with the simulation results demonstrates that the equations presented in this paper can calculate various post-wave gradients accurately. After verification, the equations can be applied to applications, including not only solution and analysis but also in the inverse design. First, the method can be applied with polar analysis to provide a new perspective and higher order parameters for the study of detonation. Second, the equations can be used for the capture of detonation waves, where both planar and axisymmetric examples show better performance. Furthermore, the equations can be used in the inverse design of detonation waves in combination with the method of characteristics, which is one of the unique benefits of the present equations.

Experiments on the Richtmyer–Meshkov instability (RMI) in a dual driver vertical shock tube (DDVST) are described. An initially planar, stably stratified membraneless interface is formed by flowing air from above and sulfur hexafluoride from below the interface location using the method of Jones & Jacobs (Phys. Fluids, vol. 9, issue 1997, 1997, pp. 3078–3085). A random three-dimensional, multi-modal initial perturbation is imposed by vertically oscillating the gas column to produce Faraday waves. The DDVST design generates two shock waves, one originating above and one below the interface, with these shocks having independently controllable strengths and interface arrival times. The shock waves have nominal strengths of $M_L=1.17$ and $M_H=1.18$ for the shock wave originating in the light and heavy gas, respectively, with these strengths chosen to result in arrested bulk interface motion following reshock. The influence of the length of the shock-to-reshock time, as well as the order of shock arrival, on the post-reshock RMI is examined. The mixing layer width grows according to $h\propto t^\theta$, where $\theta _H=0.36\pm 0.018$ (95 %) and $\theta _L=0.38\pm 0.02$ (95 %) for heavy and light shock first experiments, respectively, indicating no strong dependence on the order of shock wave arrival. Volume integrated specific turbulent kinetic energy (TKE) in the mixing layer versus time is found to decay according to $E_{tot}/\bar {\rho }\propto t^p$ with $p_H=-0.823\pm 0.06$ (95 %) and $p_L=-1.061\pm 0.032$ (95 %) for heavy and light shock first experiments, respectively. Notably, the 95 % confidence intervals do not overlap. Analysis on the influence of the shock-to-reshock time on turbulent length scales, transition criteria, spectra and mixing layer anisotropy are also presented.

In hypersonic flight the shock wave and turbulent boundary layer interaction (STBLI) sharply increases wall heat transfer that intensifies the aerodynamic heating problems. In this work the STBLI is modelled by compression ramp flow with a Mach number of 5, a Reynolds number based on momentum thickness of 4652 and a wall to recovery temperature ratio of 0.5. The aerodynamic heat generation and transport mechanisms are investigated in the interaction based on theoretical analysis and direct numerical simulation (DNS) that agrees with previous studies. A prediction correlation of wall heat flux in STBLI is deduced theoretically and validated by some representative data including the present DNS, which improves the prediction accuracy and can be applied to a wider $Ma$ range compared with the canonical Q-P theory. The correlation indicates that the sharp increase of wall heat transfer in the STBLI can be explained by the boundary layer compression and the convection transport enhancement. Based on the DNS results, the aerodynamic heat generation and transport mechanisms are revealed in the separation, recirculation and reattachment zones in the STBLI. From this perspective, the peak heat flux can be further explained by the enhancement of near-wall turbulent energy dissipation, compression aerodynamic heat generation and the near-wall turbulent transport. The generation and transport of compression aerodynamic heat reveal the underlying mechanism of the strong correlation between the peak heat flux ratios and the pressure ratios in STBLIs.

The Taylor–Maccoll (T–M) equations are the governing equations for steady inviscid irrotational axisymmetric conical flow, and have been widely applied to the design of waveriders and intakes. However, only four classic solutions have been reported: external conical flow (ECF), Busemann flow and internal conical flow of types A and B (ICFA and ICFB). In this work, the analysis of the T–M equations clarifies all possible solutions and reveals their relations. The domain where elementary solutions exist is divided into four domains. The classic Busemann and ICFB solutions share the same elementary solution as the template in a domain called the pre-shock domain, while the classic ECF and ICFA solutions belong to a domain named the ECF domain. Two new solutions, the inner flow of ECF (IECF) and degenerate conical flow (DCF), are found in the domains named after the corresponding solutions, namely the IECF and DCF domains. The IECF behaves as the mass injection supporting the classic ECF on an imaginary cone surface, while the DCF behaves as the conical expansion of a uniform flow. Furthermore, possible combinations of pre-shock solutions and supersonic post-shock solutions are clarified. The classic solutions are special cases where the pre-/post-shock solutions are combined with uniform flows. In general, the Busemann and ICFB solutions can be combined with any post-shock solutions in accord with the shock relations, including the ECF, ICFA, IECF and DCF solutions. In addition, numerical analyses are conducted to verify the validity of the two new solutions, DCF, IECF and one combined solution Busemann–ECF.

Explosive dispersal of granular media widely occurs in nature across various length scales, enabling engineering applications ranging from commercial or military explosive systems to the loss prevention industry. However, the correlation between the explosive dispersal behaviour and the structure of dispersal system is far from completely understood, thereby compromising the prediction of the explosive dispersal outcome resulting from a specific dispersal system. Here, we investigate the dispersal behaviours of densely packed particle rings driven by the enclosed pressurized gases using coarse-grained computational fluid dynamics–discrete parcel method. Distinct dispersal modes emerge from the dispersal systems with vastly varying sets of the macro- and micro-scale structural parameters in terms of the dispersal completeness and the spatial uniformity of the dispersed mass. Further investigation reveals the variation in the dispersal modes arises from the collective effects of multiscale gas–particle coupling relationships. Specifically, the macroscale coupling dictates the cyclic momentum/energy transfer between gases and particle ring as an entirety. The mesoscale coupling relates to the inter-pore gas filtration through the thickness of the particle ring, leading to the mass/energy reduction of the explosive source. The microscale coupling involves the individual particle dynamics influenced by the local flow parameters. A persistent macroscale coupling results in an incomplete dispersal which takes the form of an aggregated annular band, whereas the meso- and micro-scale couplings alter the macroscale coupling to a different extent. By incorporating the effects of the variety of structural parameters on the multiscale gas–particle coupling relationships, a non-dimensional parameter referred to as the modified mass ratio is constructed, which shows an explicit correlation with the dispersal mode. We proceed to establish a dispersal ring model in the continuum frame which accounts for the macro and meso-scale coupling effects. This model proves to be capable of successfully predicting the ideal and validated failed dispersal modes.

The effects of reshock conditions, including the interface evolution state before reshock and the second shock intensity, on interface instability induced by two successive shocks propagating in the same direction are investigated via shock-tube experiments. It is observed that the reshock promotes the interface instability, and the post-reshock perturbation evolution relates to both the pre-reshock interface evolution state and second shock intensity. For the linear evolution of the twice-shocked interface, existing models perform poorly when either the pre-reshock interface shape effect or the secondary compression effect is pronounced, as current reduction factors fail to accurately describe these effects. Besides, the reshock-induced linear amplitude growth rate shows a non-monotonic dependence on the scaled pre-reshock amplitude, primarily due to the shape effect of the pre-reshock interface. For the post-reshock nonlinear evolution, the model proposed by Zhang & Guo (J. Fluid Mech., vol. 786, 2016, pp. 47–61) offers reasonable predictions when the second shock is weak. However, when the second shock is moderately strong, the model overestimates the bubble growth and underestimates the spike evolution under the influence of the significant secondary compression effect. Furthermore, empirical linear and nonlinear models capable of describing the dependence of the post-reshock evolution on reshock conditions are proposed based on the present experimental results and existing models.

Several transition scenarios are present in a hypersonic compression-ramp flow. In our previous work (Cao et al., J. Fluid Mech., vol. 941, 2022, p. A8), a complete transition process induced by the global instability of a compression-ramp flow was revealed. In a globally stable flow, however, the transition to turbulence can be promoted by convective instabilities, which is the focus of this work. The same flow conditions as in our previous work (Mach number 7.7, Reynolds number $8.6\times 10^5$ based on the flat-plate length) are considered here. Owing to a smaller ramp angle, a weakly separated flow forms on the compression ramp, which supports no global instability. Resolvent analysis identifies low-frequency streamwise streaks as the optimal response of base flow to upstream forcing. Local stability analysis reveals Mack's second mode in the boundary layer downstream of reattachment. By introducing random disturbances upstream of separation in direct numerical simulations, we observe breakdown to turbulence downstream of reattachment. Two transition scenarios are revealed, and they are highly dependent on the amplitude of upstream disturbances. For a large amplitude, strong streamwise streaks develop near the reattachment region, which break down to turbulence quickly. However, when the disturbance amplitude is reduced, the second-mode instability dominates the transition to turbulence.

The reflection of a shock pulse at a liquid–gas interface occurs in many applications, from lithotripsy to underwater explosions and additive manufacturing. In linear theory, reflection and transmission at an interface depend only on the impedance difference, but this does not hold for a nonlinear pulse. This work develops an analytical framework for computing the reflection and transmission coefficients for an impulsive shock wave at a liquid–gas interface. The problem is treated analytically by considering idealised pulses and solving a series of consecutive Riemann problems. These correspond to the initial interaction with the interface and important subsequent wave interactions that enable a complete description of the process to be obtained. Comparisons with numerical and existing analytical approaches are made for the case of a water–air interface. In the acoustic limit, the method produces results identical to those of linear acoustic theory. As the pulse strength increases, the proposed method agrees well with numerical simulation results, whereas existing analytical methods that consider only the interface fail. We detail how a reflecting pulse can put water into tension without any incident negative pressure. It is further shown that the magnitude of the reflection coefficient decreases with increasing incident shock pressure, and the reflected pulse widens. Reflections of pulses with positive and negative pressures temporarily create negative pressure regions with greater magnitude than the incident pulse. Finally, we consider non-idealised waves. Comparisons with simulations show that the reflection characteristics can be explained qualitatively using the analytical method, and the reflection coefficients are predicted accurately.

This study comprehensively investigates the response of a combusting droplet during its interaction with a high-speed transient flow imposed by a coaxially propagating blast wave. The blast wave is generated using a specially designed miniature shock generator that produces blast waves using the wire-explosion technique, facilitating a wide range of Mach numbers (1.03 < Ms < 1.8). The experiments are performed in two configurations: open field and focused blast wave. The charging voltage and the configuration determine the Mach number (Ms) and flow characteristics. The flame is found to exhibit two major response patterns: partial extinction followed by reignition and full extinction. Increasing the Mach number (Ms > 1.1) makes the droplet flame more vulnerable to extinction. Additionally, the flame exhibits stretching and shedding, followed by reignition at lower Mach numbers (Ms < 1.06). In all cases, the flame base lifts off in response to the imposed flow, and the advection of the flame base interacting with the flame tip results in flame extinction. The entire interaction occurs in two stages: (i) interaction with the blast wave and the decaying velocity profile associated with it, and (ii) interaction with the induced flow behind the blast wave as a result of the entrainment (delayed response). Alongside the flame's response, the droplet also interacts with the flow imposed by the blast wave, exhibiting different response modes including pure deformation, Rayleigh–Taylor piercing bag breakup and shear-induced stripping.

Supersonic internal flows often exhibit multiple reflected shocks within a limited distance. These shocks can interact with each other in a complex manner due to the characteristics of the shock wave–turbulent boundary layer interaction (STBLI), including flow distortion and the relaxing boundary layer. This study aims to characterise this type of interaction and to clarify its fluid physics. A separated STBLI zone was established either upstream or downstream, and another weaker STBLI was established in the opposing position to serve as a perturbation. Time-resolved measurements were employed to characterise the mean separation and unsteadiness as the two regions approached each other, as well as their relationship. The experimental results indicated that the STBLI could affect the separation and reattachment of the other STBLI through either the decelerated or relaxing boundary layer. Despite a small deflection angle, the incident shock can amplify the low-frequency oscillations in the downstream STBLI region. Additionally, the interaction in the downstream region can be influenced by both low- and high-frequency oscillations associated with the upstream STBLI through a relaxing boundary layer. Despite the limited correlation observed between the low-frequency fluctuations in the downstream region and the boundary layer flow not far upstream, there still exists some degree of correlation between the low-frequency shock motions even when they are widely separated. Both the ‘upstream mechanism’ and ‘downstream mechanism’ have been observed, and the significance of low-frequency dynamics in the separated flow, relative to that of the upstream flow, is closely associated with interaction intensity.

Shock refraction in a gas–liquid interface is ubiquitous in nature and engineering. This study investigates the shock refraction phenomena in air–water interfaces for various inclination angles. The interface inclination angles are achieved using a tiltable vertical shock tube. The time-resolved schlieren images are compared with numerical simulations performed using the BlastFoam solver in the OpenFOAM software. The stiffened gas equation of state is used to model water in the simulations. The shock polar analysis using modified shock relations for a stiffened gas is used to elucidate the refraction patterns. A regular refraction pattern with a reflected shock wave and a bound precursor refraction with a regular reflection are observed experimentally for the first time in an air–water system. Further, a new free precursor refraction pattern with a Mach reflection is observed. The transition criteria and the corresponding boundaries for each refraction pattern are demarcated in the ($M_S, \theta _w^c$)-plane. The refraction sequence and the range for various incident shock strength regimes are also identified.

Regular reflection (RR) to Mach reflection (MR) transitions (${\rm RR}\leftrightarrow {\rm MR}$) on long wedges in steady supersonic flows have been well studied and documented. However, in a short wedge where the wedge length is small, the transition prediction becomes really challenging owing to the interaction of the expansion fan emanating from the trailing edge of the wedge with the incident shock and the triple/reflection point. The extent of this interaction depends on the distance between the wedge trailing edge and the symmetry line (Ht). This distance is a geometric combination of the distance of the wedge leading edge from the symmetry line $(H)$, the wedge angle ($\theta$) and the wedge length $(w)$. In the present study, we used the method of characteristics to model the complete wave interactions which accurately predicted shock curvatures and the reflection configurations for all ranges of the incoming flow Mach number. In the case of short wedges, the transition criterion strongly depends on the wedge length, which can be so adjusted even to eliminate the ${\rm RR}\rightarrow {\rm MR}$ transitions till the wedge angle reaches the no-reflection domain. Transition lines for both the detachment criterion and von Neumann criterion are also drawn to investigate the dual solution domain, and the reflection configurations were verified experimentally for the first time on short wedges. By using proper input configuration parameter ($w/H$), various types of shifts in the dual solution domain for short wedges are studied and categorised into three types, namely Type I, Type II and Type III.

Microvortex generators (MVGs) are a promising solution to control shock wave/turbulent boundary layer interactions (SBLIs), especially in supersonic inlets. In this study, we examine the effects of a microramp vortex generator on an SBLI generated by an oblique shock wave and a turbulent boundary layer using direct numerical simulations (DNSs). Two cases, with and without the presence of a microramp, are compared in terms of their mean and unsteady flow features at free-stream Mach number equal to 2 and friction Reynolds number at the inviscid shock impingement equal to 600. The long integration period allows us to assess how microramps affect the typical low-frequency unsteadiness observed in SBLIs, and the data generated may serve as a reference for simulations of lower fidelity or reduced order models. The analysis shows that the three-dimensional microramp wake alters the interaction region dramatically, inducing a significant spanwise modulation and topology change of the separation. For example, tornado-like structures redistribute the flow in both the spanwise and wall-normal directions inside the recirculation region. The increase in momentum close to the wall by the ramp vortices effectively delays the onset of the separation and, thus, the separation length, but at the same time leads to a significant increase in the intensity of the wall-pressure fluctuations. We then characterise the mutual interaction between the arch-like vortices around the ramp wake and the SBLI. The specific spanwise vorticity shows that these vortices follow the edge of the separation and their intensity, apart from mean compressibility effects, is not affected by the shocks. The shocks, instead, are deformed in shape by the periodic impingement of the vortices, although the spectral analysis did not reveal any significant trace of their shedding frequency in the separation region. These Kelvin–Helmholtz vortices, however, may be relevant in the closure of the separation bubble. Fourier analysis also shows a constant increase, in both value and magnitude, in the low-frequency peak all along the span, suggesting that the motion of the separation shock remains coherent while being disturbed by the arch-like vortices and oscillating at a higher frequency in absolute terms.

Predicting the transient flow fields that develop when a shock wave passes through an area expansion is a fundamental problem in compressible fluid mechanics and significant in many engineering applications. Experiments, large eddy simulations and geometrical shock dynamics are used to study the mechanism by which a normal shock wave that expands across an area expansion evolves into a uniform normal shock far downstream of it. This study analyses shock waves with moderate Mach numbers of 1.1–1.8 that expand at area ratios of up to 5. As the shock wave propagates into the expanded region, it experiences rapid deceleration, forming a non-uniform shock front. Impinging on the walls of the larger cross-section region, the shock wave reflects and generates a complex and highly transient shock pattern near the expansion region. We have found that as the shock front propagates further downstream, a laterally moving shock wave that intersects the shock front at a triple point reverberates laterally between the walls. This process effectively evens out the flow behind the incident shock front, thus reducing the variation of properties behind it. The extended duration of this process leads to significant pressure fluctuation behind the shock front. The results show that the evolution of the shock front can be scaled using the expanded region height and the velocity of the shock wave far downstream of the expansion. The results enabled the formulation of a simple empirical relation, allowing us to predict the shock velocity far downstream of gradual and abrupt area expansions.

The coupling of Richtmyer–Meshkov instability (RMI) and Kelvin–Helmholtz instability (KHI), referred to as RM-KHI, on a shock-accelerated inclined single-mode air–SF$_6$ interface is studied through shock-tube experiments, focusing on the evolution of the perturbation distributed along the inclined interface. To clearly capture the linear (overall linear to nonlinear) evolution of RM-KHI, a series of experiments with a weak (relatively strong) incident shock is conducted. For each series of experiments, various $\theta _{i}$ (angle between incident shock and equilibrium position of the initial interface) are considered. The nonlinear flow features manifest earlier and develop faster when $\theta _{i}$ is larger and/or shock is stronger. In addition, the interface with $\theta _{i}>0^{\circ }$ evolves obliquely along its equilibrium position under the effect of KHI. RMI dominates the early-time amplitude evolution regardless of $\theta _{i}$ and shock intensity, which arises from the discrepancy in the evolution laws between RMI and KHI. KHI promotes the post-early-stage amplitude growth and its contribution is related positively to $\theta _{i}$. An evident exponential-like amplitude evolution behaviour emerges in RM-KHI with a relatively strong shock and large $\theta _{i}$. The linear model proposed by Mikaelian (Phys. Fluids, vol. 6, 1994, pp. 1943–1945) is valid for RM-KHI within the linear period. In contrast, the adaptive vortex model (Sohn et al., Phys. Rev. E, vol. 82, 2010, p. 046711) can effectively predict both the interface morphology and overall amplitude evolutions from the linear to nonlinear regimes.

In gamma-ray binaries neutron star is orbiting a companion that produces a strong stellar wind. We demonstrate that observed properties of ‘stellar wind’–‘pulsar wind’ interaction depend both on the overall wind thrust ratio, as well as more subtle geometrical factors: the relative direction of the pulsar’s spin, the plane of the orbit, the direction of motion, and the instantaneous line of sight. Using fully 3D relativistic magnetohydrodynamical simulations we find that the resulting intrinsic morphologies can be significantly orbital phase-dependent: a given system may change from tailward-open to tailward-closed shapes. As a result, the region of unshocked pulsar wind can change by an order of magnitude over a quarter of the orbit. We calculate radiation maps and synthetic light curves for synchrotron (X-ray) and inverse-Compton emission (GeV-TeV), taking into account $\gamma $–$\gamma $ absorption. Our modelled light curves are in agreement with the phase-dependent observed light curves of LS5039.

The unsteady mechanism of unstart flow for an inlet with rectangular-to-elliptical shape transition (REST) under the off-design condition at a Mach of 4 is investigated using the delay detached eddy simulation method. With the help of numerical simulations, the unsteady dynamics, especially the low-frequency characteristics of the REST inlet unstart flow, as well as the self-sustaining mechanism, is investigated. The instantaneous flow illustrates the unsteady phenomena of the REST unstart flow, including the interaction between the cowl-closure leading edge (CLE) shock and the shear layer, breathing of the separation bubble, flapping of the separation shock, instability of the shear layer and vortex shedding along the shear layer. The spectral analysis reveals that the lower frequency dynamics is associated with the breathing of the separation bubble and the flapping motion of the separation shock wave, while the higher frequency is related to the instability of the shear layer affected by cowl-closure leading edge shock and the formation of shedding vortices. Further, coherence analysis shows that the contribution of these flow structures dominating the low-frequency dynamics couple with each other. Based on the dynamic mode decomposition results, the characteristics that contribute to the unsteady behaviour of unstart flow are summarized. The streamwise vortices downstream of the separation and the shedding vortices are believed to be the main driving force of the global low-frequency unsteadiness of the REST inlet unstart flow under the off-design condition. Moreover, the CLE shock plays an important role in the process during the dominant flow structure conversion from the backflow within the separation bubble into elongated streamwise structures.

Wall temperature has a significant effect on shock wave/turbulent boundary layer interactions (STBLIs) and has become a non-negligible factor in the design process of hypersonic vehicles. In this paper, direct numerical simulations are conducted to investigate the wall temperature effects on STBLIs over a 34° compression ramp at Mach number 6. Three values of the wall-to-recovery-temperature ratio (0.50, 0.75 and 1.0) are considered in the simulations. The results show that the size of the separation bubble declines significantly as the wall temperature decreases. This is because the momentum profile of the boundary layer becomes fuller with wall cooling, which means the near-wall fluid has a greater momentum to suppress flow separation. An equation based on the free-interaction theory is proposed to predict the distributions of the wall pressure upstream of the corner at different wall temperatures. The prediction results are generally consistent with the simulation results (Reynolds number Reτ ranges from 160 to 675). In addition, the low-frequency unsteadiness is studied through the weighted power spectral density of the wall pressure and the correlation between the upstream and downstream. The results indicate that the low-frequency motion of the separation shock is mainly driven by the downstream mechanism and that wall cooling can significantly suppress the low-frequency unsteadiness, including the strength and streamwise range of the low-frequency motions.