Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-29T09:05:58.728Z Has data issue: false hasContentIssue false
  • English
  • Français

Low Defect Density Microcrystalline-Si Deposited by the Hot Wire Technique

Published online by Cambridge University Press:  10 February 2011

A. H. Mahan ,
M. Vanecek ,
A. Poruba ,
V. Vorlicek ,
R. S. Crandall  and
D. L. Williamson
A. H. Mahan
Affiliation:
National Renewable Energy Laboratory, Golden, CO 80401
M. Vanecek
Affiliation:
Insitiute of Physics, Academy of Sciences of the Czech Republic, Prague 6, CZ-16253 Czech Republic
A. Poruba
Affiliation:
Insitiute of Physics, Academy of Sciences of the Czech Republic, Prague 6, CZ-16253 Czech Republic
V. Vorlicek
Affiliation:
Insitiute of Physics, Academy of Sciences of the Czech Republic, Prague 6, CZ-16253 Czech Republic
R. S. Crandall
Affiliation:
National Renewable Energy Laboratory, Golden, CO 80401
D. L. Williamson
Affiliation:
Physics Department, Colorado School of Mines, Golden, CO 80401
Get access

Abstract

The optical and electronic properties of a series of microcrystalline silicon (μ-Si) films, deposited by the hot wire (HW) technique, are reported. Preliminary results suggest, using moderate H2 /SiH4 dilution ratios and substrate temperatures (320°C), high filament temperatures, and no H gas purifier, that the subgap absorption for these films, measured using the constant photocurrent (CPM) method, can be as low as that obtained for films deposited by the very high frequency glow discharge (VHF-GD) technique. The film dark conductivities of the HW samples, ranging as low as 2.0 × 10−8 (ohm cm)−1, lend further credance to these low defect values. At the same time, the optical absorption in the region > 1.6 eV is higher than that previously observed for the VHF-GD deposited samples. The present results, discussed in the context of the film microcrystalline fraction, suggest that there is no unique, good quality, low defect density μ-Si material, and that different deposition techniques can be used to successfully deposit device quality gc-Si. We also present optical and structural data for films deposited at lower substrate temperatures and higher deposition rates, and suggest combinations of deposition parameters to be used that may further improve the electronic properties of these films.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 507: Symposium A – Amorphous & Microcrystalline Silicon Technology 1998 , 1998 , 825
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1) Williams, M. J., Wang, C., and Lucovsky, G., AIP Conf. Proc. 234, 211 (1991).Google Scholar
2) Meier, J., Dubail, S., Fischer, D., Selvan, J.A. Anna, Vaucher, N. Pellaton, Platz, R., Ch. Hof, Fluckiger, R., Kroll, U., Wyrsch, N., Torres, P., Kepner, H., Shah, A., Uefert, K.D., Proc. 13th European Photovoltaic Solar Energy Conf., p. 1445 (1995).Google Scholar
3) Meier, J., Dubail, S., Cuperus, J., Kroll, U., Platz, R., Torres, P., Selvan, J. A. Anna, P./ Pernet, Beck, N., Vaucher, N. Pellaton, Hof, Ch., Fischer, D., Keppner, H., and Shah, A., 17th ICAMS, Budapest, 1997, to appear in J. non-Cryst. Sol. (1998).Google Scholar
4) Mahan, A. H. and Vanecek, M., AIP Conf. Proc. 234, 211 (1991).Google Scholar
5) Wu, Y., Stephen, J. T., Han, D. X., Rutland, J. M., Crandall, R. S., and Mahan, A. H., Phys. Rev. Lett. 77, 2049 (1996).Google Scholar
6) Liu, X., White, B. E. Jr., Pohi, R. O., Iwaniczko, E., Jones, K. M., Mahan, A. H., Nelson, B. N., Crandall, R. S., and Veprek, S., Phys. Rev. Lett. 78, 4418 (1997).Google Scholar
7) Mahan, A. H., Williamson, D. L., and Furtak, T. E., MRS Symp. Proc. 467, 657 (1997).Google Scholar
8) Mahan, A. H., Carapella, J. C., and Gallagher, A. C., U.S. Patent 5,397,737 (1995).Google Scholar
9) Based upon the pyrometer and filament current tables, currents of 13.5A, 15A, and 16A correspond to approximate filament temperatures of 1900°C, 2025°C, and 2100°C respectively.Google Scholar
10) Vanecek, M., Kocka, J., Poruba, A., and Fejfar, J., J. Appl. Phys. 78, 6203 (1995).Google Scholar
11) Vanecek, M., Poruba, A., Remes, Z., Beck, N., and Nesladek, M., 17th ICAMS, Budapest, 1997, to appear in J. non-Cryst. Sol. (1998).Google Scholar
12) Diehl, F., Herbst, W., Schroeder, B., and Oechsner, H., MRS Symp. Proc. 467, 451 (1997).Google Scholar
13) Puigdollers, J., Bertomeu, J., Cifre, C., Andreu, J., and Delgado, J. C., MRS Symp. Proc. 377, 63 (1995).Google Scholar
14) Conde, J. P., Brogueira, P., Castanha, R., and Chu, V., MRS Symp. Proc. 420, 357 (1996).Google Scholar
15) Rath, J. K., Barbon, A., and Schropp, R. E. I., 17th ICAMS, Budapest, 1997, to appear in J. non-Cryst. Sol. (1998).Google Scholar