Specimen quality is vital to (scanning) transmission electron microscopy (TEM) investigations. In particular, thin specimens are required to obtain excellent high-resolution TEM images. Conventional focused ion beam (FIB) preparation methods cannot be employed to reliably create high quality specimens much thinner than 20 nm. We have developed a method for in situ target preparation of ultrathin TEM lamellae by FIB milling. With this method we are able to routinely obtain large area lamellae with coplanar faces, thinner than 10 nm. The resulting specimens are suitable for low kV TEM as well as scanning TEM. We have demonstrated atomic resolution by Cs-corrected high-resolution TEM at 20 kV on a FIB milled Si specimen only 4 nm thick; its amorphous layer measuring less than 1 nm in total.

Transmission electron microscopy (TEM), fluorescence microscopy, and confocal Raman microscopy can be used to characterize ultrastructural and compositional heterogeneity of plant cell walls. In this study, TEM observations revealed the ultrastructural characterization of Cornus alba L. fiber, vessel, axial parenchyma, ray parenchyma, and pit membrane between cells, notably with the ray parenchyma consisting of two well-defined layers. Fluorescence microscopy evidenced that cell corner middle lamella was more lignified than adjacent compound middle lamella and secondary wall with variation in lignification level from cell to cell. In situ Raman images showed that the inhomogeneity in cell wall components (cellulose and lignin) among different cells and within morphologically distinct cell wall layers. As the significant precursors of lignin biosynthesis, the pattern of coniferyl alcohol and aldehyde (joint abbreviation Lignin-CAA for both structures) distribution in fiber cell wall was also identified by Raman images, with higher concentration occurring in the fiber secondary wall where there was the highest cellulose concentration. Moreover, noteworthy was the observation that higher concentration of lignin and very minor amounts of cellulose were visualized in the pit membrane areas. These complementary microanalytical methods provide more accurate and complete information with regard to ultrastructural and compositional characterization of plant cell walls.

Experimental results from the first monochromated and aberration-corrected scanning transmission electron microscope operated at 200 kV are described. The formation of an electron probe with a diameter of less than 0.2 nm at an energy width significantly under 0.3 eV and its planned application to the chemical analysis of nanometer-scale structures in materials science are described. Both energy and spatial resolution will benefit from this: The monochromator improves the energy resolution for studies of energy loss near edge structures. The Cs corrector allows formation of either a smaller probe for a given beam current or yields, at fixed probe size, an enhanced beam current density using a larger condenser aperture. We also point out another advantage of the combination of both components: Increasing the convergence angle by using larger condenser apertures in an aberration-corrected instrument will enlarge the undesirable chromatic focus spread. This in turn influences spatial resolution. The effect of polychromatic probe tails is proportional to the product of convergence angle, chromatic aberration constant, and energy spread. It can thus be compensated for in our new instrument by decreasing the energy width by the same factor as the beam convergence is increased to form a more intense probe. An alternative in future developments might be hardware correction of the chromatic aberration, which could eliminate the chromatic probe spread completely.

The determination of cell volumes and biomass offers a means of comparing the standing stocks of auto- and heterotrophic microbes of vastly different sizes for applications including the assessment of the flux of organic carbon within aquatic ecosystems. Conclusions about the importance of particular genotypes within microbial communities (e.g., of filamentous bacteria) may strongly depend on whether their contribution to total abundance or to biomass is regarded. Fluorescence microscopy and image analysis are suitable tools for determining bacterial biomass that moreover hold the potential to replace labor-intensive manual measurements by fully automated approaches. However, the current approaches to calculate bacterial cell volumes from digital images are intrinsically biased by the models that are used to approximate the morphology of the cells. Therefore, we developed a generic contour based algorithm to reconstruct the volumes of prokaryotic cells from two-dimensional representations (i.e., microscopic images) irrespective of their shape. Geometric models of commonly encountered bacterial morphotypes were used to verify the algorithm and to compare its performance with previously described approaches. The algorithm is embedded in a freely available computer program that is able to process both raw (8-bit grayscale) and thresholded (binary) images in a fully automated manner.

Few simple labeling methods exist for simultaneous fluorescence and electron microscopy of bacteria and biofilms. Here we describe the synthesis, characterization, and application of fluorescent nanoparticle quantum dot (QD) conjugates to target microbial species, including difficult to label Gram-negative strains. These QD conjugates impart contrast for both environmental scanning electron microscopy (ESEM) and fluorescence microscopy, permitting observation of living and fixed bacteria and biofilms. We apply these probes for studying biofilms extracted from perennial cold springs in the Canadian High Arctic, which is a particularly challenging system. In these biofilms, sulfur-metabolizing bacteria live in close association with unusual sulfur mineral formations. Following simple labeling protocols with the QD conjugates, we are able to image these organisms in fully-hydrated samples and visualize their relationship to the sulfur minerals using both ESEM and fluorescence microscopy. We then use scanning transmission electron microscopy to observe precipitated sulfur around individual cells and within the biofilm lattice. All combined, this information sheds light on the possible mechanisms of biofilm and mineral structure formation. These new QD conjugates and techniques are highly transferable to many other microbiological applications, especially those involving Gram-negative bacteria, and can be used for correlated fluorescence and electron microscopy.

Due to the intrinsic evaporation properties of the material studied, insufficient mass-resolving power and lack of knowledge of the kinetic energy of incident ions, peaks in the atom probe mass-to-charge spectrum can overlap and result in incorrect composition measurements. Contributions to these peak overlaps can be deconvoluted globally, by simply examining adjacent peaks combined with knowledge of natural isotopic abundances. However, this strategy does not account for the fact that the relative contributions to this convoluted signal can often vary significantly in different regions of the analysis volume; e.g., across interfaces and within clusters. Some progress has been made with spatially localized deconvolution in cases where the discrete microstructural regions can be easily identified within the reconstruction, but this means no further point cloud analyses are possible. Hence, we present an ion-by-ion methodology where the identity of each ion, normally obscured by peak overlap, is resolved by examining the isotopic abundance of their immediate surroundings. The resulting peak-deconvoluted data are a point cloud and can be analyzed with any existing tools. We present two detailed case studies and discussion of the limitations of this new technique.

Through a correlative analytical approach encompassing backscattered electron scanning electron microscopy (BSE-SEM), energy dispersive X-ray spectroscopy (EDX), and micro-Raman spectroscopy, the composition of the mineralized biofilm around a dental implant, retrieved due to peri-implantitis, was investigated. The mineralized biofilm contains two morphologically distinct regions: (i) bacteria-containing zones (Bact+), characterized by aggregations of unmineralized and mineralized bacteria, and intermicrobial mineralization, and (ii) bacteria-free zones (Bact−), comprised mainly of randomly oriented mineral platelets. Intramicrobial mineralization, within Bact+, appears as smooth, solid mineral deposits resembling the morphologies of dental plaque bacteria. Bact− is associated with micrometer-sized Mg-rich mineral nodules. The Ca/P ratio of Bact+ is higher than Bact−. The inorganic phase of Bact+ is carbonated apatite (CHAp), while that of Bact− is predominantly octacalcium phosphate (OCP) and whitlockite (WL) inclusions. Compared with native bone, the inorganic phase of Bact+ (i.e., CHAp) exhibits higher mineral crystallinity, lower carbonate content, and lower Ca/P, C/Ca, Mg/Ca, and Mg/P ratios. The various CaPs found within the mineralized dental biofilm (CHAp, OCP, and WL) are related to the local presence/absence of bacteria. In combination with BSE-SEM and EDX, micro-Raman spectroscopy is a valuable analytical tool for nondestructive investigation of mineralized dental biofilm composition and development.

Acidocalcisomes are acidic calcium storage compartments described initially in trypanosomatid and apicomplexan parasites, and recently found in other unicellular eukaryotes. The aim of this study was to identify the presence of acidocalcisomes in the plant trypanosomatid Phytomonas françai. Electron-dense organelles of P. françai were shown to contain large amounts of oxygen, sodium, magnesium, phosphorus, potassium, calcium, iron, and zinc as determined by X-ray microanalysis, either in situ or when purified using iodixanol gradient centrifugation or by elemental mapping. The presence of iron is not common in other acidocalcisomes. In situ, but not when purified, these organelles showed an elongated shape differing from previously described acidocalcisomes. However, these organelles also possessed a vacuolar H+-pyrophosphatase (V-H+-PPase) as determined by biochemical methods and by immunofluorescence microscopy using antibodies against the enzyme. Together, these results suggest that the electron-dense organelles of P. françai are homologous to the acidocalcisomes described in other trypanosomatids, although with distinct morphology and elemental content.

A method to characterize open-cell nanoporous materials with atom probe tomography (APT) has been developed. For this, open-cell nanoporous gold with pore diameters of around 50 nm was used as a model system, and filled by electron beam-induced deposition (EBID) to obtain a compact material. Two different EBID precursors were successfully tested—dicobalt octacarbonyl [Co2(CO)8] and diiron nonacarbonyl [Fe2(CO)9]. Penetration and filling depth are sufficient for focused ion beam-based APT sample preparation. With this approach, stable APT analysis of the nanoporous material can be performed. Reconstruction reveals the composition of the deposited precursor and the nanoporous material, as well as chemical information of the interfaces between them. Thus, it is shown that, using an appropriate EBID process, local chemical information in three dimensions with sub-nanometer resolution can be obtained from nanoporous materials using APT.

When using bifunctional core@shell catalysts, the stability of both the shell and core–shell interface is crucial for catalytic applications. In the present study, we elucidate the stability of a CuO/ZnO/Al2O3@ZSM-5 core@shell material, used for one-stage synthesis of dimethyl ether from synthesis gas. The catalyst stability was studied in a hierarchical manner by complementary environmental transmission electron microscopy (ETEM), scanning electron microscopy (SEM) and in situ hard X-ray ptychography with a specially designed in situ cell. Both reductive activation and reoxidation were applied. The core–shell interface was found to be stable during reducing and oxidizing treatment at 250°C as observed by ETEM and in situ X-ray ptychography, although strong changes occurred in the core on a 10 nm scale due to the reduction of copper oxide to metallic copper particles. At 350°C, in situ X-ray ptychography indicated the occurrence of structural changes also on the µm scale, i.e. the core material and parts of the shell undergo restructuring. Nevertheless, the crucial core–shell interface required for full bifunctionality appeared to remain stable. This study demonstrates the potential of these correlative in situ microscopy techniques for hierarchically designed catalysts.

The ability to transfect Apicomplexan parasites has revolutionized the study of this important group of pathogens. The function of specific genes can be explored by disruption of the locus or more subtly by introduction of altered or tagged versions. Using the transgenic reporter gene green fluorescent protein (GFP), cell biological processes can now be studied in living parasites and in real time. We review recent advances made using GFP-based experiments in the understanding of protein trafficking, organelle biogenesis, and cell division in Toxoplasma gondii and Plasmodium falciparum. A technical section provides a collection of basic experimental protocols for fluorescent protein expression in T. gondii. The combination of the in vivo marker GFP with an increasingly diverse genetic toolbox for T. gondii opens many exciting experimental opportunities, and emerging applications of GFP in genetic and pharmacological screens are discussed.

Quantification of immunostaining is a widely used technique in pathology. Nonetheless, techniques that rely on human vision are prone to inter- and intraobserver variability, and they are tedious and time consuming. Digital image analysis (DIA), now available in a variety of platforms, improves quantification performance: however, the stability of these different DIA systems is largely unknown. Here, we describe a method to measure the reproducibility of DIA systems. In addition, we describe a new image-processing strategy for quantitative evaluation of immunostained tissue sections using DAB/hematoxylin-stained slides. This approach is based on image subtraction, using a blue low pass filter in the optical train, followed by digital contrast and brightness enhancement. Results showed that our DIA system yields stable counts, and that this method can be used to evaluate the performance of DIA systems. The new image-processing approach creates an image that aids both human visual observation and DIA systems in assessing immunostained slides, delivers a quantitative performance similar to that of bright field imaging, gives thresholds with smaller ranges, and allows the segmentation of strongly immunostained areas, all resulting in a higher probability of representing specific staining. We believe that our approach offers important advantages to immunostaining quantification in pathology.

Twinning plays an important role in phase transformations and can have significant effects on microstructural evolution. Different roles of twinning in the development of microstructures during precipitation and phase transformations are reviewed and illustrated with examples from investigations by high-resolution electron microscopy, including the effect of multiple twinning on the development of Ge precipitates in Al-Ge and Ag-Ge alloys, the twin dissociation of grain boundaries in Au, the formation of hexagonal Si at twin intersections and the effect of twin boundaries on the equilibrium shape of Pb inclusions in Al.

Quercus suber L. has been investigated with special attention to the stem bark and its cork formation layer, but excluding the roots. Roots are the location of infection by pathogens such as Phytophthora cinnamomi responsible for the tree's sudden death. It is widely accepted that suberin establishes boundaries within tissues, serves as a barrier against free water and ion passage, and works as a shield against pathogen attacks. We followed the suberization of young secondary roots of cork oak. The first suberin deposition detectable by transmission electron microscopy (TEM) and neutral red (NR) was in the endoderm Casparian strips. Casparian strips are not detected by Sudan red 7B and Fluorol yellow (FY) that specifically stain lamellae suberin. Reaction to Sudan was verified in the endodermis and later on in phellem cells that resulted from the phellogen. Under TEM, the Sudan and FY-stained cells showed clear suberin lamellae while the newer formed phellem cells displayed a distinct NR signal compared to the outermost phellem cells. We concluded that suberin chemical components are arranged differently in the cell wall according to the physiological role or maturation stage of a given tissue.

The advent of simultaneous energy dispersive X-ray spectroscopy (EDS) data collection has vastly improved the phase separation capabilities for electron backscatter diffraction (EBSD) mapping. A major problem remains, however, in distinguishing between multiple cubic phases in a specimen, especially when the compositions of the phases are similar or their particle sizes are small, because the EDS interaction volume is much larger than that of EBSD and the EDS spectra collected during spatial mapping are generally noisy due to time limitations and the need to minimize sample drift. The backscatter electron (BSE) signal is very sensitive to the local composition due to its atomic number (Z) dependence. BSE imaging is investigated as a complimentary tool to EDS to assist phase segmentation and identification in EBSD through examination of specimens of meteorite, Cu dross, and steel oxidation layers. The results demonstrate that the simultaneous acquisition of EBSD patterns, EDS spectra, and the BSE signal can provide new potential for advancing multiphase material characterization in the scanning electron microscope.

Electron backscatter diffraction (EBSD) techniques were used to characterize “hot-rolled” quenched and partitioned microstructures produced via Gleeble thermal simulations representing a hot-strip cooling practice for steel. In particular, EBSD was utilized to positively identify the morphology and location of retained austenite, to qualitatively distinguish martensite from ferrite, and in an attempt to identify transition carbides. Large pools of retained austenite and some thin films were accurately indexed; however, there was some disparity between austenite volume fractions measured by EBSD and those measured by X-ray diffraction. Due to similarities between the crystal structures of martensite and ferrite (body centered tetragonal versus body centered cubic, respectively), martensite could not be distinguished from ferrite by indexing of diffraction patterns; however, martensite could qualitatively be distinguished from ferrite by regions of low image quality based on the very high dislocation density of martensite.

We evaluated the depth resolution of annular dark-field (ADF) scanning confocal electron microscopy (SCEM) with a stage-scanning system by observation of nanoparticles. ADF-SCEM is a three-dimensional (3D) imaging technique that we recently proposed. An ADF-SCEM instrument involves a pinhole aperture before a detector for rejecting electrons from the out-of-focal plane in a specimen and an annular aperture under the specimen for collecting only scattered electrons. The stage-scanning system enables us to directly obtain optical slice images perpendicular and parallel to an optical axis at a desired position. In particular, the parallel slices visualize the elongation of nanoparticles along the optical axis, which depends on the depth resolution. ADF-SCEM effectively reduced the elongation length of the nanoparticles sufficiently to demonstrate depth sectioning, in comparison with scanning transmission electron microscopy and bright-field SCEM. The experimentally obtained length was nearly equal to the theoretically estimated one from the probe size considering the experimental conditions. Furthermore, we applied this ADF-SCEM technique to analysis of the 3D position of catalytic nanoparticles on carbon nanostructures.