This study presents a novel configuration of a cuboidal quad-port ultra-wideband multiple-input and multiple-output antenna with WLAN rejection characteristics. The designed antenna consists of four F-shaped elements backed by a partial ground plane. A 50 Ω microstrip line is used to feed the proposed structure. The geometry of the suggested antenna exhibits an overall size of 23 × 23 × 19 mm3, and the antenna produces an operational bandwidth of 7.6 GHz (3.1–10.7 GHz). The notched band characteristic at 5.4 GHz is accomplished by loading a pair of spiral electromagnetic bandgap structures over the ground plane. Besides this, other diversity features such as envelope correlation coefficient, and diversity gain are also evaluated. Furthermore, the proposed antenna system provides an isolation of −15 dB without using any decoupling structure. Therefore, to validate the reported design, a prototype is fabricated and characterized. The overall simulated performance is observed in very close agreement with it's measured counterpart.

This paper describes a multiple-input multiple-output (MIMO) antenna for low millimeter (mm)-wave applications based on dielectric resonators. This is the first time that a filtering response is used in conjunction with an MIMO antenna operating at a low mm-wave frequency. The antenna is simulated using an asymmetrical U-shaped aperture and a microstrip line feed. The suggested filtenna has two distinguishing characteristics: (i) the diversity parameters of the proposed MIMO are increased by including pattern and spatial diversity, and (ii) the proposed feed mechanism of a dielectric resonator provides the filtering response. Between the two ports, a metallic plate tilts the radiation pattern by 45°. The anti-parallel locations of the ports increase the isolation value by >30 dB. To validate the performance of the suggested antenna, the proposed filtenna was built and confirmed. The proposed antenna operates between the frequencies 27.9 and 28.5 GHz. Within the operating frequency range, the observed gain is ~4.5 dBi. On the contrary, the gain suppression level beyond the operational frequency range is ~15 dB. The stable radiation properties and high diversity parameter values of the suggested filtenna make it an effective solution for 5G Internet of Things sensing applications.

This paper describes a compact and efficient rectenna based on a dual-diode microstrip rectifier at 2.45 GHz. This circuit has been designed and optimized using a global analysis technique which associates electromagnetic and circuit approaches. Due to the differential topology of the rectifier, neither input low-pass filter nor via-hole connections are needed. This makes the structure more compact reducing losses. Measurements of a single rectenna element show 83% efficiency over an optimal load of 1050 Ω at a power density of 0.31 mW/cm2. To increase the received RF power and then increase dc power over the load, identical rectennas have been interconnected to form arrays. Two and four elements rectenna arrays, connected either in parallel or in series, have been developed. It was shown that by properly choosing the interconnection topology and the optimal output load, higher dc voltage or dc power have been obtained. The four-element series-connected array can provide experimentally up to 3.85 times output dc voltage compared to the single rectenna. The parallel-connected rectenna arrays generate approximately 2.15 and 3.75 times output dc power for two and four elements, respectively.

A small ultra-wideband (UWB) patch antenna for microwave breast imaging (MWI) applications is shown off in this paper. However, to improve the antenna performance relating to the bandwidth (BW), the radiating element of the suggested antenna is modified by adding slits in the patch as well as the ground plane. The proposed prototype has a relatively small size of 20 × 19 × 1.6 mm3 and it accomplishes a return loss below −10 dB (S11< −10 dB) at an overall BW of 7 GHz (4–11 GHz) with more than 3 dBi realized gain. The antenna is designed and simulated by using a finite integration technique-based simulator. In this way, the characteristics of the fabricated antenna are measured to examine the antenna performance. Indeed, the fidelity factor of face-to-face (FtF) and side-by-side (SbS) scenarios are also noticed for the same frequency range. In the final analysis, a simulation model of the antennas, that operate as a transceiver, and a breast phantom model with tumor sample is proposed for detecting cancerous tumor cells within the breast. Hence, the proposed approach is suitable for UWB based MWI applications in tumor cell detection.

The implementation and application of single-layer fully-planar extended-composite right-/left-handed transmission lines (E-CRLH TLs) in substrate-integrated waveguide (SIW) technology are presented. The multiband CRLH behavior of these artificial lines is explained by considering the lumped element equivalent circuit model. The potential of these lines for dual-band and quad-band applications is demonstrated by designing and fabricating a quad-band Y-junction power divider and two dual-band band-pass filters. The main relevant advantage of SIW-based E-CRLH TLs over other E-CRLH lines is fabrication simplicity, since only a single metal layer must be etched and lumped elements are avoided. The fabricated prototypes exhibit very reasonable performance. It is remarkable that for dual-band band-pass filters, standard Chebyshev responses can be obtained to a very good approximation.

An array of patch-antennas with meandering-gaps on an optical modulator is proposed for wireless millimeter-wave beam-steering through high-speed radio-over-fiber systems. Wireless millimeter-wave can be received by the array of patch-antennas and directly modulated to lightwave by the optical modulator. The wireless millimeter-wave can be steered using the meandering-gaps at the patch-antennas by controlling interaction between millimeter-wave and lightwave electric fields in electro-optic modulation. The basic operation and analysis of the proposed device are discussed. In the experiment, 5 × 5 antenna array in 40 GHz millimeter-wave bands was designed and realized for device characterization and demonstration to wireless millimeter-wave beam-steering. There were five variations of wireless millimeter-wave beam-steering for one-dimensional in xz- or yz-planes that can be obtained with wireless millimeter-wave steerable beams of about ±30°. Additionally, 25 variations of wireless beam-steering can be obtained for two dimension in xyz-space through orthogonal optical modulation. The proposed device is promising to be applied in millimeter-wave/tera-hertz bands for future directional wireless communication and sensing with high-speed and high-resolution operation.

A multi-input multi-output (MIMO) antenna is designed and discussed for multi-band applications. The constituent antennas are composed of four L-shaped elements and a ground plane. When placed beside each other to form a MIMO antenna, a T-bar shaped parasitic structure is also embedded between the antennas on the backside of the substrate to increase the inter-element isolation. The triple-band performance of the antenna is observed at 2.15–2.73 GHz, 3.1–3.9 GHz, and 5.04–6 GHz. The isolation level of more than 20 is seen over the operating frequency range. The fabricated prototype of the MIMO antenna size is very compact (20 × 40 mm), printed on the FR4 substrate. Based on simulation and experimental results, the proposed design is useful for WiMAX and WLAN applications.

A wideband four element triangular dielectric resonator antenna (TDRA) has been designed and fabricated by using 50 Ω coaxial probe feed. The input and radiation characteristics of the proposed antenna have been extracted through Ansoft HFSS and CST Microwave Studio simulation software and compared with the experimental results. The simulated results have been in good agreement with the experimental results. The proposed antenna characteristics have also been compared with the same dimensions of the single element TDRA, and found enhancement in bandwidth with lower resonant frequency. Its performance has also been compared with same area (equal to proposed antenna) of single element TDRA. The proposed antenna provides nearly 37% bandwidth (|S11| < −10 dB) at a resonant frequency of 5.45 GHz with 4.76 dBi peak gain. The symmetry and uniformity in the radiation patterns is obtained consistently for the entire operating bandwidth. The proposed antenna shows consistently symmetric monopole type radiation pattern with low cross polarization for WLAN (IEEE 802.16) and WiMAX applications. The performance of the proposed antenna has been compared with some similar type of dielectric resonator antenna (DRA) shapes and it has been observed that TDRA is taking very less radiation area for giving better performance than other DRA shapes.

For the requirements of low mutual-coupling MIMO antennas for WLAN, a new complementary split-ring resonator (CSRR) unit cell is introduced in this paper. A microstrip-fed Vivaldi antenna array is designed for WLAN applications, where compact triple-band gap-complementary split-ring resonator unit cells are loaded between two antennas to examine the effect of unit cells on the rate of mutual-coupling reduction. By inserting the CSRR, the final design offered an improvement in decoupling by 8.5, 10.5, and 18 dB at 3.65, 4.9, and 5.8 GHz, respectively, compared with the reference antenna. By suppressing surface waves, antenna gain and front-to-back ratio are improved.

In this paper, the small- and large-signal modeling of InP heterojunction bipolar transistors (HBTs) in transferred substrate (TS) technology is investigated. The small-signal equivalent circuit parameters for TS-HBTs in two-terminal and three-terminal configurations are determined by employing a direct parameter extraction methodology dedicated to III–V based HBTs. It is shown that the modeling of measured S-parameters can be improved in the millimeter-wave frequency range by augmenting the small-signal model with a description of AC current crowding. The extracted elements of the small-signal model structure are employed as a starting point for the extraction of a large-signal model. The developed large-signal model for the TS-HBTs accurately predicts the DC over temperature and small-signal performance over bias as well as the large-signal performance at millimeter-wave frequencies.

A combined class-AB and a Doherty power amplifier conceived for microwave backhaul in the 7 GHz frequency band are here presented and compared. They are fabricated in the same GaN monolithic process and have identical total active device periphery. For the given application, the linearity-efficiency trade-off for the two architectures is discussed. The two modules have been thoroughly characterized in linear and non-linear continuous wave conditions. Then, to evaluate linearity under the actual operative conditions, a system level characterization has been carried out, applying a modulated input signal and comparing the spectral responses of the two amplifiers with and without digital predistortion. A saturated output power of 40 dBm has been achieved by both circuits. At 6 dB of output back-off, the Doherty amplifier shows an efficiency of 33%, 10 points higher than that of the class-AB module. On the other hand, system level measurements show that, adopting the same predistorter complexity to comply with the reference standard emission masks, the Doherty amplifier needs at least 1 dB of extra back-off. This negatively affects its efficiency, therefore reducing the advantages it can claim with respect to the class-AB amplifier in continuous wave condition.

A novel 1 × 4 phased array elliptical inverted T-shaped slotted sectored patch antenna with defected ground structure (DGS), resonate at proposed ultra-wide tetra band at 28, 43, 51, and 64 GHz with high gain and beam-steering capabilities is presented. An inverted T-shaped slotted stub is used with the sectored patch to achieve ultra-wideband properties. In order to resonate the antenna at four different bands, DGS of round bracket slot is etched on the ground. The 1 × 4 phased arrays are used at the top edge and bottom edge of mobile PCB with high gain. The simulation results show that the antenna has four ultra-wide bands: 25.8–29.7, 40.6–44.6, 49.2–53.1, and 62.2–74 GHz with a maximum gain of 16.5 dBi at 51 GHz. The phased array antenna is capable to steer its main beam within ±30° at the 26, 28, and 43 GHz, using appropriate phase shifts of each antenna element. The proposed millimeter wave antenna is particularly suitable for cellular infrastructures and can be a candidate for emerging 5G mobile applications. The availability of an additional 11.8 GHz (62.2–74 GHz) of contiguous unlicensed spectrum will allow the launching of new exciting wireless services.

In this paper, a novel design of ultra-wide stop-band single-side single-layer frequency selective surface (FSS) is presented. The unit cell of the proposed FSS is designed using the combination of conventional square loop and cross (CSLC). To enhance the bandwidth of this structure, an additional cross is inserted in all the four quadrants of CSLC. The stop-band transmission bandwidth assuming −10 dB threshold is found to be 128.94% (2.16–10 GHz) which is 34.33% more as compared to the bandwidth of CSLC. The unit cell with a dimension of 16 × 16 mm2 is printed on one side of an FR4 substrate. The design is fabricated and the measured results are found to be in good agreement with the simulated results. The design provides excellent stability for both transverse magnetic and transverse electric polarizations. The design is very flexible, where any resonant frequency can be achieved by changing the length of unit cell. The design is useful in many applications such as antenna gain enhancement, electromagnetic wave shielding for Wi-Fi/5G systems, and other Internet of Things-based applications.

Radar sensors are key components of modern driver assistance systems. The application of such systems in urban environments for safety applications is the primary goal of the project “Radar on Chip for Cars” (RoCC). Major outcomes of this project will be presented and discussed in this contribution. These outcomes include the specification of radar sensors for future driver assistance systems, radar concepts, and integration technologies for silicon-germanium (SiGe) MMICs, as well as the development and evaluation of a system demonstrator. A radar architecture utilizing planar antennas and highly integrated components will be proposed and discussed with respect to system specifications. The developed system demonstrator will be evaluated in terms of key parameters such as field of view, distance, and angular separability. Finally, as an outlook a new mid range radar (MRR) will be introduced incorporating several concepts and technologies developed in this project.

Delay time measurements are a commonly used technique for the characterization of dielectric materials. Especially with regard to the characterization of water–solid mixtures like soil or grain delay time measurements, e.g., time domain reflectometry offers a powerful method. However, the accuracy of reflection measurements is limited due to multiple reflections caused by inhomogenities of the environmental material of the sensor. This contribution deals with an improved sensor design based on time domain transmission (TDT) measurements. Thus, the first received impulse includes the necessary information. Multiple reflections are received at later time steps and their influence on the measurement accuracy is nearly negligible. To improve the performance and the applicability of the designed sensor, a cost–efficient TDT system is designed, which is integrated in the sensor. Additionally, a so-called “concentric reversion coupler” is used, which offers the possibility to perform TDT measurements without the necessity of external measuring ports.

A printed multiband Multi-Input Multiple-Output (MIMO) antenna is proposed in this paper. This MIMO antenna system comprises two symmetric printed monopole antennas. Each antenna element consists of multiple bend lines, producing four resonant modes and covering the GSM900, PCS, LTE2300, and 5G bands. Simulated and measured results prove that the proposed MIMO antenna can be applied to traditional 2G, 3G, 4G, and present 5G mobile communication. By etching four inverted L-shaped grooves on its ground plate, mutual coupling between the adjacent antenna elements has been suppressed. This makes the |S21| at all four resonant modes is lower than −40 dB. In addition, its low coupling mechanism has been analyzed by surface current distribution. The designed multiband MIMO antenna provides an idea of reference to realize low mutual coupling between antenna elements, which is also realizable in infrared or optical regimes with appropriate designs.

This paper proposes a unique, first of its kind fabrication technique for the making of textile antennas. A novel method that provides scope for automation in textile antenna production is presented here. A completely integrated textile antenna fabrication method that eliminates the tasks of positioning and fastening of the various components of a patch antenna is discussed. The technique employs multilayer weaving for the production of a wearable antenna on a cotton substrate. Silver yarn is used for the conductive regions of the textile antenna. Two layers of woven cotton serve to isolate the radiating patch from the ground plane of the antenna. The designed antenna was chosen to operate at the frequency of 2.45 GHz for Wireless Local Area Network. The built prototype resonated at 2.43 GHz with a |S11|of −18.62 dB. The integrated textile antenna exhibited a gain of 1.06 dBi at 2.43 GHz.

A microwave design for an industrial scale applicator of a continuous microwave assisted depolymerization of polyethylene terephthalate (PET) has been developed. The cavity is designed for use in combination with an Archimedean screw pump to transport the reaction material, surrounded by a cylindrical pipe with a diameter of 250 mm and a length of 250 mm at the 2.45 GHz ISM band. The proposed design is modular and can be easily expanded for the heating of longer reactor tubes. Simulation results show that a homogeneous heating of the process material along the screw axis can be achieved by using a novel cavity design which is based on the TE1,0,x– rectangular waveguide cavity mode. The achieved design provides high energy efficiency with a reflected power of less than 10%. It is robust against changes in the permittivity of the reactants. The electromagnetic design is based on the dielectric properties of the solvolytic reaction mixture measured in the relevant temperature range. It is verified over the full range of the expected permittivities.

A circularly polarized high-power antenna with higher-order mode excitation (TM01) is presented in this paper. The proposed structure consists of metal plates placed on the conical horn antenna's aperture for achieving TM01 to circular polarized TE11 mode conversion at the output. The structure is simulated on CST Microwave Studio. The designed antenna exhibits high gain and a directive radiation pattern. The axial ratio of the proposed structure is below 3 dB. The simulated and measured reflection coefficient for TM01 mode excitation is below −10 dB over a frequency range of 2.95–3.13 GHz. The structure is purely metallic, and the calculated high-power microwave (HPM) capability is up to the MW level. The proposed antenna is helpful for portable HPM systems.

Self-protection deceptive jammers create at the radar receiver output multiple-false targets that are impossible to isolate in both time and frequency domains. In this paper, we introduce a novel technique based on fractional Fourier transform (FrFT) to discriminate between the true target echo and those false targets in the case of frequency-shifting jammers. In fact, we exploit the capability of the FrFT to resolve, in a matched manner, spectra that are overlapping in time and frequency. This is a property that cannot be achieved using a standard matched filter. The theoretical analysis of this technique is presented and its effectiveness is verified by simulation.