The interaction of intense, ultrashort laser pulses with ordered nanostructure arrays offers a path to the efficient creation of ultra-high-energy density (UHED) matter and the generation of high-energy particles with compact lasers. Irradiation of deuterated nanowires arrays results in a near-solid density environment with extremely high temperatures and large electromagnetic fields in which deuterons are accelerated to multi-megaelectronvolt energies, resulting in deuterium–deuterium (D–D) fusion. Here we focus on the method of fabrication and the characteristics of ordered arrays of deuterated polyethylene nanowires. The irradiation of these array targets with femtosecond pulses of relativistic intensity and joule-level energy creates a micro-scale fusion environment that produced $2\times {10}^6$ neutrons per joule, an increase of about 500 times with respect to flat solid CD2 targets irradiated with the same laser pulses. Irradiation with 8 J laser pulses was measured to generate up to 1.2 × 107 D–D fusion neutrons per shot.

We numerically and experimentally investigate the multi-pulsing mechanism in a dispersion-managed mode-locked Yb-doped fiber laser. Multi-pulsing occurs primarily owing to the inherent filtering effect of the chirped fiber Bragg grating. The spectral filtering effect restricts the spectral broadening induced by self-phase modulation and causes extra loss, leading to a decreased pump power threshold for the multi-pulsing state. Numerical simulations show that multi-pulsing emerges at a lower pump power when the spectral filter bandwidth becomes narrower. In the experiment, the spectral width increases as the net cavity dispersion approaches zero. Pulses with wider spectral widths experience more loss from the spectral filtering effect, leading to a decreased pump power threshold for multi-pulsing. Therefore, the net cavity dispersion also has an impact on the multi-pulsing threshold. Based on this conclusion, we devise a strategy to obtain single-pulsing operation with the shortest pulse width and the highest pulse energy.

The first experimental measurements of intense (${\sim }7\times 10^{19}~ {\rm W}~ {\rm cm}^{-2}$) laser-driven terahertz (THz) radiation from a solid target which is preheated by an intense pulse of laser-accelerated protons is reported. The total energy of the THz radiation is found to decrease by approximately a factor of 2 compared to a cold target reference. This is attributed to an increase in the scale length of the preformed plasma, driven by proton heating, at the front surface of the target, where the THz radiation is generated. The results show the importance of controlling the preplasma scale length for THz production.

We present detailed characterization of laser-driven fusion and neutron production ($\sim {10}^5$/second) using 8 mJ, 40 fs laser pulses on a thin (<1 μm) D${}_2$O liquid sheet employing a measurement suite. At relativistic intensity ($\sim 5\times {10}^{18}$ W/cm${}^2$) and high repetition rate (1 kHz), the system produces deuterium–deuterium (D-D) fusion, allowing for consistent neutron generation. Evidence of D-D fusion neutron production is verified by a measurement suite with three independent detection systems: an EJ-309 organic scintillator with pulse-shape discrimination, a ${}^3\mathrm{He}$ proportional counter and a set of 36 bubble detectors. Time-of-flight analysis of the scintillator data shows the energy of the produced neutrons to be consistent with 2.45 MeV. Particle-in-cell simulations using the WarpX code support significant neutron production from D-D fusion events in the laser–target interaction region. This high-repetition-rate laser-driven neutron source could provide a low-cost, on-demand test bed for radiation hardening and imaging applications.

We have optimized the input pulse width and injection time to achieve the highest possible output pulse energy in a double-pass laser amplifier using two Nd:YAG rods. For this purpose, we have extended the Frantz–Nodvik equation by simultaneously including both spontaneous emission and pump energy variation. The effective pump energy of the flash lamp was 8.84 J for each gain medium. The energy of 1 J could be amplified to an output energy of 12.17 J with the maximum achieved extraction efficiency of 63.18% when an input pulse having a pulse width of 168 $\unicode[STIX]{x03BC}$s is sent 10 $\unicode[STIX]{x03BC}$s after the absorbed pump energy becomes the maximum value.

FERMI, the seeded free electron laser (FEL) in operation in Italy, is providing the User Community with unique fully coherent radiation, in the wavelength range 100–4 nm. FERMI is the first FEL fully synchronized by means of optical fibers. The optical timing system ensures an ultra-stable phase reference to its distributed clients. Several femtosecond longitudinal diagnostics verify the achieved performance; the bunch length monitor (BLM) and the bunch arrival monitor (BAM) will be presented in this paper. Feedback systems play a crucial role to guarantee the needed long-term electron beam stability. A real-time infrastructure allows shot-to-shot communication between front-end computers and the servers. Orbit feedbacks are useful in machine tuning, whereas longitudinal feedbacks control electron energy, compression and arrival time. A flexible software framework allows a rapid implementation of heterogeneous multi-input–multi-output (MIMO) longitudinal loops simply by selecting the appropriate sensors and actuators.

The stimulated Brillouin scattering phase conjugation mirror (SBS-PCM) based on liquid media is widely used in high-power laser systems due to its robust thermal load capacity, high energy conversion efficiency and improved beam quality. Nevertheless, with an increase in the pump repetition rate, thermally-induced blooming and optical breakdown can emerge, leading to distortions in the Stokes beam. In this study, we delved into the thermal effects in liquid SBS-PCMs employing hydrodynamic analysis, establishing a relationship between beam profile distortion and the thermal convection field. We calculated the temperature and convection velocity distribution based on the pump light parameters and recorded the corresponding beam profiles. The intensities of the beam profiles were modulated in alignment with the convection directions, reaching a velocity peak of 2.85 mm/s at a pump pulse repetition rate of 250 Hz. The residual sum of squares (RSS) was employed to quantify the extent of beam profile distortion relative to a Gaussian distribution. The RSS escalated to 7.8, in contrast to 0.7 of the pump light at a pump pulse repetition rate of 500 Hz. By suppressing thermal convection using a high-viscosity medium, we effectively mitigated beam distortion. The RSS was reduced to 0.7 at a pump pulse repetition rate of 500 Hz, coinciding with a twentyfold increase in viscosity, thereby enhancing the beam quality. By integrating hydrodynamic analysis, we elucidated and mitigated distortion with targeted solutions. Our research offers an interdisciplinary perspective on studying thermal effects and contributes to the application of SBS-PCMs in high-repetition-rate laser systems by unveiling the mechanism of photothermal effects.

We present laboratory measurement and theoretical analysis of silicon K-shell lines in plasmas produced by Shenguang II laser facility, and discuss the application of line ratios to diagnose the electron density and temperature of laser plasmas. Two types of shots were carried out to interpret silicon plasma spectra under two conditions, and the spectra from 6.6 Å to 6.85 Å were measured. The radiative-collisional code based on the flexible atomic code (RCF) is used to identify the lines, and it also well simulates the experimental spectra. Satellite lines, which are populated by dielectron capture and large radiative decay rate, influence the spectrum profile significantly. Because of the blending of lines, the traditional $G$ value and $R$ value are not applicable in diagnosing electron temperature and density of plasma. We take the contribution of satellite lines into the calculation of line ratios of He-$\unicode[STIX]{x1D6FC}$ lines, and discuss their relations with the electron temperature and density.

With the development of high-volume manufacturing for very-large-scale integrated circuits, the purity of the light source in the extreme ultraviolet lithography (EUVL) system needs to fulfil extreme requirements in order to avoid thermal effect, optical distortion and critical dimension errors caused by out-of-band radiations. This paper reviews the key technologies and developments of the spectral purity systems for both a free-standing system and a built-in system integrated with the collector. The main challenges and developing trends are also discussed, with a view towards practical applications for further improvement. Designing and manufacturing spectral purity systems for EUVL is not a single task; rather, it requires systematic considerations for all relevant modules. Moreover, the requirement of spectral purity filters drives the innovation in filtering technologies, optical micromachining and advanced metrology.

We demonstrate that the methodology of frequency-resolved optical gating (FROG) is applicable to time-resolved reflection spectroscopy of a plasma mirror in the vacuum-ultraviolet (VUV) region. Our recent study [R. Itakura et al. Opt. Express 23, 10914 (2015)] has shown that a VUV waveform can be retrieved from a VUV reflection spectrogram of a plasma mirror formed on a fused silica (FS) surface by irradiation with an intense femtosecond laser pulse. Simultaneously, the increase in the reflectivity with respect to the Fresnel reflection of the unexcited FS surface can be obtained as a time-dependent reflectivity of the plasma mirror. In this study, we update the FROG analysis procedure using the least-square generalized projections algorithm. This procedure can reach convergence much faster than the previous one and has no aliasing problem. It is demonstrated that a significantly chirped VUV pulse as long as 1 ps can be precisely characterized.

We develop a splicing technology of Ti:sapphire crystals for a high-energy chirped pulse amplifier laser system that can suppress the parasitic lasing to improve the amplification efficiency compared to a large-size single Ti:sapphire crystal amplifier. Theoretical investigations on the characteristics of the amplifier with four splicing Ti:sapphire crystals, such as parasitic-lasing suppression and amplification efficiencies, are carried out. Some possible issues resulting from this splicing technology, including spectral modulation, stretching or splitting of the temporal profile, and the sidelobe generation in the spatial domain (near field and far field), are also investigated. Moreover, the feasibility of the splicing technology is preliminarily demonstrated in an experiment with a small splicing Ti:sapphire crystals amplifier. The temporal profile and spatial distribution of the output pulse from the splicing Ti:sapphire crystal amplifier are discussed in relation to the output pulse from a single Ti:sapphire crystal amplifier.

Pumped by rectangular-shaped dissipative soliton resonance (DSR) pulses at 1030 nm, selective excitations of Raman Stokes lines of up to third order with extinction ratios of 8 dB and fifth order with extinction ratios of 4 dB are demonstrated experimentally. The rectangular DSR pulses are generated from a dual-amplifier ytterbium-doped figure-of-eight mode-locked laser constructed using all $10~\unicode[STIX]{x03BC}\text{m}$-core-diameter large-mode-area fibers. By varying the two pump powers, the peak power of the output DSR pulses can be continuously tuned from 10 W to 100 W and from 30 W to 200 W, respectively, for two different lengths of the nonlinear amplifying loop mirror inside the cavity. High-frequency components are found to correspond to parts of the pulse in the trailing edge when two bandpass filters are used to separate the propagated pulse. Consequently, it provides an all-fiber technique to achieve selective excitation of the Raman shift by adjusting the peak power of the DSR pulse.

A high-energy, alignment-insensitive, injection-seeded Q-switched Ho:yttrium aluminum garnet (YAG) single-frequency laser is developed. Both the slave Q-switched laser and the seed laser are Ho:YAG ring lasers based on a pair of corner cubic reflectors. The seed laser has an available power of 830 mW at 2096.667 nm. At 100 Hz, the Q-switched Ho:YAG laser provides a single-frequency pulsed output using injection-seeded technology. The 7.3 mJ single-frequency pulse energy from the slave laser has a pulse width of 161.2 ns and is scaled to 33.3 mJ after passing through the Ho:YAG single-pass amplifier. According to the measurement results of the heterodyne beating technique, the single-frequency pulse has a half-width of 4.12 MHz.

Ultrafast laser pulses provide unique tools to manipulate magnetization dynamics at femtosecond timescales, where the interaction of the electric field usually dominates over the magnetic field. Recent proposals using structured laser beams have demonstrated the possibility to produce regions where intense oscillating magnetic fields are isolated from the electric field. In these conditions, we show that technologically feasible tesla-scale circularly polarized high-frequency magnetic fields induce purely precessional nonlinear magnetization dynamics. This fundamental result not only opens an avenue in the study of laser-induced ultrafast magnetization dynamics, but also sustains technological implications as a route to promote all-optical non-thermal magnetization dynamics both at shorter timescales – towards the sub-femtosecond regime – and at THz frequencies.

The acoustic pulse emitted from the Bragg peak of a laser-accelerated proton bunch focused into water has recently enabled the reconstruction of the bunch energy distribution. By adding three ultrasonic transducers and implementing a fast data analysis of the filtered raw signals, I-BEAT (Ion-Bunch Energy Acoustic Tracing) 3D now provides the mean bunch energy and absolute lateral bunch position in real-time and for individual bunches. Relative changes in energy spread and lateral bunch size can also be monitored. Our experiments at DRACO with proton bunch energies between 10 and 30 MeV reveal sub-MeV and sub-mm resolution. In addition to this 3D bunch information, the signal strength correlates also with the absolute bunch particle number.

We present an experimental study of the dynamics of shocks generated by the interaction of a double-spot laser in different kinds of targets: simple aluminum foils and foam–aluminum layered targets. The experiment was performed using the Prague PALS iodine laser working at 0.44 μm wavelength and irradiance of a few 1015 W/cm2. Shock breakouts for pure Al and for foam-Al targets have been recorded using time-resolved self-emission diagnostics. Experimental results have been compared with numerical simulations. The shocks originating from two spots move forward and expand radially in the targets, finally colliding in the intermediate region and producing a very strong increase in pressure. This is particularly clear for the case of foam layered targets, where we also observed a delay of shock breakout and a spatial redistribution of the pressure. The influence of the foam layer doped with high-Z (Au) nanoparticles on the shock dynamics was also studied.

We present experimental and numerical investigations of high-energy mid-infrared filamentation with multi-octave-spanning supercontinuum generation (SCG), pumped by a 2.4 μm, 250 fs Cr:ZnSe chirped-pulse laser amplifier. The SCG is demonstrated in both anomalous and normal dispersion regimes with YAG and polycrystalline ZnSe, respectively. The formation of stable and robust single filaments along with the visible-to-mid-infrared SCG is obtained with a pump energy of up to 100 μJ in a 6-mm-long YAG medium. To the best of the authors’ knowledge, this is the highest-energy multi-octave-spanning SCG from a laser filament in a solid. On the other hand, the SCG and even-harmonic generation based on random quasi-phase matching (RQPM) are simultaneously observed from the single filaments in a 6-mm-long polycrystalline ZnSe medium with a pump energy of up to 15 μJ. The numerical simulations based on unidirectional pulse propagation equation and RQPM show excellent agreement with the measured multi-octave-spanning SCG and even-harmonic generation. They also reveal the temporal structure of mid-infrared filaments, such as soliton-like self-compression in YAG and pulse broadening in ZnSe.

Temporal contrast directly affects the interaction between ultraintense and ultrashort pulse lasers with matter. Seed laser sources with broad bandwidth and high temporal contrast are significant for overall temporal contrast enhancement. The technique of cascaded nonlinear processes with optical parametric amplification and second-harmonic generation is demonstrated for high temporal contrast seed source generation. Within 40 ps before the main pulse, the temporal contrast reaches over 1011. The pulse energy and duration of the high-contrast pulse are 112 μJ and 70 fs, respectively. Considering its high beam quality and stability, this laser source can serve as a high-quality seed for Nd:glass-based ultraintense and ultrashort pulse laser facilities.

The intensity distributions of a high-power broadband laser beam passing through a nonlinear optical medium with defects and then propagating in free space are investigated based on the general nonlinear Schrödinger equation and the split-step Fourier numerical method. The influences of the bandwidth of the laser beam, the thickness of the medium, and the defects on the light intensity distribution are revealed. We find that the nonlinear optical effect can be suppressed and that the uniformity of the beam can be improved for a high-power broadband laser beam with appropriate wide bandwidth. It is also found that, under the same incident light intensity, a thicker medium will lead to a stronger self-focusing intensity, and that the influence of defects in the optical elements on the intensity is stronger for a narrowband beam than for a broadband beam.

The large-aperture pulse compression grating (PCG) is a critical component in generating an ultra-high-intensity, ultra-short-pulse laser; however, the size of the PCG manufactured by transmission holographic exposure is limited to large-scale high-quality materials. The reflective method is a potential way for solving the size limitation, but there is still no successful precedent due to the lack of scientific specifications and advanced processing technology of exposure mirrors. In this paper, an analytical model is developed to clarify the specifications of components, and advanced processing technology is adopted to control the spatial frequency errors. Hereafter, we have successfully fabricated a multilayer dielectric grating of 200 mm × 150 mm by using an off-axis reflective exposure system with Φ300 mm. This demonstration proves that PCGs can be manufactured by using the reflection holographic exposure method and shows the potential for manufacturing the meter-level gratings used in 100 petawatt class high-power lasers.