The work reported here was an experimental study of the combined influence of a sandpaper rough surface and a stream turbulence upon laminar and transitional boundary layers. Data correlations were obtained using the previously determined parameter of an equivalent Nikuradse size of roughness. These correlations are derived for the development of the laminar layer in thickness and profile shape factor, for the onset and the length of transition and for the distribution of intermittency through transition. Further fundamental differences in flow behaviour from those in a rough pipe have been found to add to those already reported.

A simplified analysis indicates that the increase in profile drag of an aerofoil due to an isolated roughness element is, in general, different from the drag of the element measured on a flat plate with the same free-stream velocity. This “magnification” effect is caused chiefly by the effect of the pressure gradients on the boundary layer downstream of the roughness element.

The degree of magnification is not closely approximated by the ratio of local to free-stream dynamic pressure and, in many typical cases, the contribution to the drag due to roughness elements may be seriously under-estimated in this way.

Measurements of the effect of the initial boundary-layer thickness on the subsequent development of a turbulent boundary-layer in an adverse pressure gradient support the theoretical conclusions.

This paper describes an evaluation of the longitudinal flying qualities of a generic blended-wing-body (BWB) transport aircraft at low speed flight conditions. Aerodynamic data was obtained from several sources and integrated into the equations of motion of a typical BWB configuration in order to provide a reasonable basis for flying qualities assessment. The control requirements to trim are enumerated for a representative range of cg position and static margin over the typical range of approach speeds for both stable and unstable configurations. The linear dynamic characteristics of the unaugmented airframe are also described for the same range of stability margin. Subsequent work describes the development of a rate command-attitude hold command and stability augmentation system configured to comply with representative modern handling criteria. Finally, the flight dynamics of the augmented aircraft are described after refinement of the control law by means of piloted simulation in a fixed base flight simulator.

This paper is one of a series addressing the need for simple, yet accurate, methods for the estimation of cruise fuel burn and other important aircraft performance parameters. Here, a previously published, constant Reynolds number model for turbofan-powered, civil transport aircraft is extended to include Reynolds number effects. Provided the variation of temperature with pressure is known, the method is applicable to flight in any atmospheric conditions. For a given aircraft, cruising in a given atmosphere, there is a single Mach number and Flight Level pair, at which the fuel burn per unit distance travelled through the air has an absolute minimum value. Both these quantities depend upon the Reynolds number, which, in turn, depends upon the aircraft weight and the atmospheric vertical temperature profile. Simple, explicit expressions are developed for all parameters at the optimum condition. These are shown to be in close agreement with numerical solutions of the governing equations. It is found that typical operational mass and temperature profile variations can change cruise fuel burn rate by several percent. In the International Standard Atmosphere, when the speed and altitude deviate from their optimum values, the fuel burn penalty is reduced slightly relative to the constant Reynolds number case. By way of example, the method is used to estimate the minimum fuel, speed-versus-height trajectory for cruise in a realistic atmosphere.

For each aircraft, cruise fuel burn is found to be governed by six independent parameters. All are constants. Two are simple, involving only size and weight, whereas four are complex and must be determined by either theoretical, or empirical, means. The estimation of these quantities will be considered in Part 2.

A forward spike attached to a blunt body significantly alters its flow field characteristics and influences aerodynamic characteristics at hypersonic flow due to formation of separated flow and re-circulation region around the spiked body. An experimental investigation was performed to measure aerodynamic forces for spikes blunt bodies with a conical, hemispherical and flat-face spike at Mach 6 and at an angle-of-attack range from 0° to 8° and length-to-diameter L/D ratio of spike varies from 0.5 to 2.0, where L is the length of the spike and D is diameter of blunt body. The shape of the leading edge of the spiked blunt body reveals different types of flow field features in the formation of a shock wave, shear layer, flow separation, re-circulation region and re-attachment shock. They are analysed with the help of schlieren pictures. The shock distance ahead of the hemisphere and the flat-face spike is compared with the analytical solution and is showing satisfactory agreement with the schlieren pictures. The influence of geometrical parameters of the spike, the shape of the spike tip and angle-of-attack on the aerodynamic coefficients are investigated by measuring aerodynamic forces in a hypersonic wind tunnel. It is found that a maximum reduction of drag of about 77% was found for hemisphere spike of L/D = 2.0 at zero angle-of-attack. Consideration for compensation of increased pitching moment is required to stabilise the aerodynamic forces.

Bird strike is a major consideration when designing fans for civil aero engines. Current methods rely on impact tests and structural optimisation but it is highly desirable to have predictive numerical models to assess the aerodynamic and aeroelastic stability of bird-damaged fan assemblies. A detailed feasibility study towards such a prediction capability, consisting of a CFD solver coupled to a finite element representation of the structure, is reported in this paper. A whole-assembly model was used for both the fluid and the structural domains, an approach necessitated by the loss of cyclic symmetry due to one or more blades undergoing plastic deformation under the effect of the bird impact. It was assumed that two consecutive blades had suffered unequal amount of bird damage, the so-called heavy and medium-damaged blades.

The flows induced by incompressible jets have been analysed for two-dimensional and axisymmetric jets emerging at right angles from an infinite plane surface. In particular, the pressure distribution on the surface has been predicted by replacing the jet with a line sink of variable strength. The theory takes account of the size of the blowing slot or nozzle and is in good agreement with experiment in both cases.

To reduce aircraft emissions to the atmosphere, the fuel burn from aircraft has to be reduced. For long flights, the cruise is the phase where the most significant reduction can be obtained. A new horizontal profile optimisation methodology to achieve lower emissions is described in this article. The impact of wind during a flight can reduce the flight time, either by taking advantage of tailwinds or by avoiding headwinds. A set of alternative trajectories are evaluated to determine the quickest flight time, and therefore, the lowest fuel burn. To determine the expected amount of fuel reduction, the performance databases used on actual FMS devices, were used. These databases represent the flight performance of commercial aircraft.

In recent years there has been considerable interest in the possibility of providing high speed aircraft with the capability of vertical or short take-off and landing (V/STOL). One method for achieving V/STOL is to use lifting engines or fans, the aerodynamic interference effects of which are not yet fully understood. Experimental work on this problem has been done by Jordinson, Otis, Vogler and research workers at the British Aircraft Cor-poration, but no satisfactory theoretical analysis is known. The object of this paper is to put forward a semi-empirical method for predicting the aerodynamic interference of an exhausting jet on a uniform mainstream flow past a wing.

The class of incompressible axially-symmetric laminar viscous flows considered are exact invariant (similarity) solutions of the Navier- Stokes equations. The functional forms of the velocity components are deduced by group-theoretic arguments. The system of governing partial differential equations is reduced to a system of ordinary differential equations and these in turn are reduced to a single first order non-linear ordinary differential equation for the dimensionless tangential velocity component. The general solution of this equation is obtained in terms of hypergeometric functions.

The classes of laminar viscous flows bounded by a right conical surface or by right inner and outer conical surfaces with a common apex obtainable from the previously mentioned (similar) solutions of the Navier-Stokes equation are studied. Suction/injection velocities (inversely proportional to the distance from the apex) normal/parallel to the conical boundaries are admissible for the classes of flows considered. If the flow is bounded by impermeable conical surfaces, then it is shown that these solutions of the Navier-Stokes equation imply that it must be identically quiescent.

When the bounding cones are not impermeable, closed solutions for the single-cone case are found in terms of elementary functions. A numerical example of such a flow, with fluid injected normal to the conical boundary, is given. Such a simplification of the hypergeometric functions entering into the problem, however, cannot be achieved in the two-cone case.

Boat-tailing of aft bodies may affect the base pressure through two mechanisms: firstly by changing the angle between the approaching flow at separation and the reattachment surface, and secondly by distorting the boundary layer through the favourable pressure gradient (which can be particularly severe in the presence of a sharp corner on the body). The first effect is isolated here by tests on inclined backward-facing steps with a fully developed turbulent boundary layer at separation, at free-stream Mach numbers of 1.75 and 2.4. It is found that the base pressure increases significantly with boat-tail angle; the data have been correlated taking explicit account of the boundary layer effect, modifying and extending the approach adopted by Nash. Charts are provided for quick estimation of base pressure in engineering calculations. Some of the earlier data on boat-tailed bases, on re-examination in the light of the present correlation, suggest that strongly distorted boundary layers at separation affect the base pressure appreciably. Several features of the measured reattachment pressure distributions, including their internal similarity, are also discussed.

This paper describes the analysis and the minimum weight optimisation of a fuselage composite stiffened panel made from carbon/epoxy material and stiffened by five omega stringers. The panel investigated inside the European project MAAXIMUS is studied using a fast tool, which relies on a semi-analytical procedure for the analysis and on genetic algorithms for the optimisation. The semi-analytical approach is used to compute the buckling load and to study the post-buckling response. Different design variables are considered during the optimisation, such as the stacking sequences of the skin and the stiffener, the geometry and the cross-section of the stiffener. The comparison between finite element and fast tool results reveals the ability of the formulation to predict the buckling load and the post-buckling response of the panel. The reduced CPU time necessary for the analysis and the optimisation makes the procedure an attractive strategy to improve the effectiveness of the preliminary design phases.

The health monitoring and damage prognosis of aerospace hotspots is important for reducing maintenance costs and increasing in-service capacity of aging aircraft. One of the leading causes of structural failure in aerospace vehicles is fatigue damage. Based on the physical mechanism of damage nucleation and growth, a physics-based multiscale model is considered for fatigue damage assessment in metallic aircraft structures. A guided-wave based sensing approach is utilised to enable effective damage detection in a common structural hotspot: a lug joint. Finite element analysis is carried out with piezoelectric wafers bonded to the host structure and the simulated sensor signals are analysed. A damage classification strategy is developed, which integrates physically motivated time-frequency approaches with advanced stochastic modelling techniques. In particular, a variational Bayesian learning scheme is used to estimate the optimal model complexity automatically from the data, adapting the classifier for real-time use. Classification performance is studied as a function of signal-to-noise ratio and results are reported for the detection of fatigue crack damage in the lug joint. An adaptive hybrid prognosis model is proposed, which estimates the residual useful life of structural hotspots using damage condition information obtained in real-time.

The main objective of the project is to develop and validate the use of a fuel cell based power system for the propulsion of more/all electric aircraft. The Rapid 200-FC two-seater electric-motor-driven aeroplane which is powered by fuel cells is at present being completed and will be validated during a flight test in Autumn 2009. Several configurations have been evaluated in order to install the new energy and propulsion system on board while maintaining the centre of gravity within allowable limits. The fuel cell system and the electric motor are being integrated on board. The FC stack will be able to deliver a maximum continuous power of 20kW. A battery pack has to guarantee another 20kW of maximum continuous power for a limited time period (15 minutes), during take-off, climbing and, in the case of emergency, during landing.

The main goal of the project is to validate the overall high performance of an all electric aircraft system which is capable of remaining aloft for one hour. A parametric analysis has also been carried out to evaluate which key technologies influence the performance of future aircraft to the greatest extent.

The influence of flow compressibility on a highly-cambered inverted aerofoil in ground effect is presented, based on two-dimensional computational studies. This type of problem has relevance to open-wheel racing cars, where local regions of high-speed subsonic flow form under favourable pressure gradients, even though the maximum freestream Mach number is typically considerably less than Mach 0·3. An important consideration for CFD users in this field is addressed in this paper: the freestream Mach number at which flow compressibility significantly affects aerodynamic performance. More broadly, for aerodynamicists, the consequences of this are also considered. Comparisons between incompressible and compressible CFD simulations are used to identify important changes to the flow characteristics caused by density changes, highlighting the inappropriateness of incompressible simulations of ground effect flows for freestream Mach numbers as low as 0·15.

Although the deployment of carbon fibre structural components has enjoyed wide success on smaller aircraft, their acceptance on larger transport airframes is less sanguine – especially in the case of primary structure applications where the increasing out of plane loads found on the larger airframes have exposed the weak interlaminar properties of the layered material system. This has led to an overreliance on mechanical attachments to suppress these through thickness failures, which ultimately degrades structural performance and increases manufacturing costs. Until these resin dominated failure modes can be dealt with more effectively, without adversely affecting the in plane properties of the laminate, the true weight-savings potential afforded by carbon fibre material systems will be difficult to attain. This paper describes how researchers at NASA-LaRC and The Boeing Company are working to develop a next generation stitched composite design solution that addresses the fundamental challenges in achieving improved structural performance and reduced fabrication costs for large carbon fibre airframe structures.

Flow separation is a source of aerodynamic inefficiency, by using vortex generators flow separation can be controlled. This is of particular benefit to flows around bodies which are susceptible to separated flows, such as bodies in ground effect. Previous studies on the ability of dimples to produce vortices for flow mixing concerned heat transfer applications. Experimental measurements using Laser Doppler Anemometry (LDA) were taken in the wake of the Tyrrell026 aerofoil (Rec = 0·5 × 105) with a dimple array machined in the surface. Results for a dimple array of three rows placed forward of x/c = 0·23 with 1·5D dimple to dimple spacing, showed significant flow recovery in the wake. The velocity deficit of u/Uo,min = −0·1 recovered to u/Uo,min = 0·3 with the dimple array and the size of the wake reduced by 50%; at α = 10°, h/c = 0·313. The positive effect of the dimple array on the wing reduced as the wing was brought closer to the ground.

This study examines the performance of two axisymmetric nozzles which were designed to produce uniform, parallel flow with nominal Mach numbers of 4 and 8. A free-piston-driven shock tube was used to supply the nozzle with high-temperature, high-pressure test gas. The inviscid design procedure treated the nozzle expansion in two stages. Close to the nozzle throat, the nozzle wall was specified as conical and the gas flow was treated as a quasi-one-dimensional chemically-reacting flow. At the end of the conical expansion, the gas was assumed to be calorically perfect and a contoured wall was designed (using Method-of-Characteristics) to convert the source flow into a uniform and parallel flow at the end of the nozzle. Performance was assessed by measuring Pitot pressures across the exit plane of the nozzles and, over the range of operating conditions examined, the nozzles produced satisfactory test flows. However, there were flow disturbances in the Mach 8 nozzle flow that persisted for significant times after flow initiation.

Stratford's analysis of the laminar boundary layer near separation uses two physical ideas. In the outer part of the boundary layer, where viscous effects are small, the development is given by the condition that the total head is constant along streamlines, apart from a second-order correction for viscosity. Near the wall, however, viscous forces must balance the pressure forces, and the profile adjusts itself accordingly. Quantitatively these ideas yield a simple formula for predicting separation, which has been found to be particularly accurate.

In this paper it is indicated how the same approach may be used to yield the full distribution of skin friction along the wall. Further, the effects of suction may be incorporated into the method. Physically, suction affects the outer part of the boundary layer in that the streamlines are drawn towards the wall when suction is applied. At the wall, the balance between viscous and pressure forces is influenced by the momentum of the fluid which is sucked away. When these effects are accounted for quantitatively, the resulting formula for the skin friction is still very simple.

Several examples are considered, and comparison is made with exact theory and with approximate results by other methods. It is indicated that the method has a useful range of validity.

—Since flow separation occurs readily from a highly swept leading edge, but gives rise in general to a steady flow, it is proposed that the rational approach to the aerodynamic design of slender wings is to attempt to control, rather than to suppress, these separations. This leads to the suggestion that the leading edges should be sharp, and that the wing should be shaped so as to make them attachment lines at one attitude (the design attitude) at which classical wing theory can be applied. It is argued, further, that if the leading edge separations are to develop regularly with change of attitude of the wing, separation must occur only from the trailing edge at the design attitude; and the velocity field favourable to boundary layer development without separation forward of the trailing edge is discussed. Subject to the restrictions thus imposed on the design, low drag is sought at the design attitude. This leads to the consideration of a particular class of doubly curved mean surfaces satisfying the leading edge condition, onto which thickness distributions are superposed so as to provide favourable velocity fields together with low drag. A number of examples are considered, using slender thin wing theory for flexibility, to illustrate the manner in which plan form and thickness distributions affect the pressure distribution, and to indicate the relatively high lift/drag ratios which seem feasible. Some consideration is given to the limitations of the theory used and to the further developments which seem desirable.